http://www.datasheet4u.com

900,000+ Datasheet PDF Search and Download

Datasheet4U offers most rated semiconductors datasheets pdf





Coilcraft
Coilcraft

1008HQ-68NXJLC Datasheet Preview

1008HQ-68NXJLC Datasheet

Chip Inductors

No Preview Available !

1008HQ-68NXJLC pdf
Document 190-1
Chip Inductors– 1008HQ (2520)
• Highest Q factors of any Coilcraft chip this body size, roughly
20% higher than our popular 1008CS and HS parts.
• Exceptional SRFs, tight tolerance and batch consistency
Coilcraft Designer’s Kit C323 contains samples of all
5% inductance tolerance parts. Kits with 2% tolerance
are also available.To order, contact Coilcraft or purchase
on-line at http://order.coilcraft.com.
Part number1
1008HQ-3N0X_L_2
1008HQ-4N1X_L_
1008HQ-7N8X_L_2
1008HQ-10NX_L_
1008HQ-12NX_L_
1008HQ-18NX_L_
1008HQ-22NX_L_
1008HQ-33NX_L_
1008HQ-36NX_L_
1008HQ-39NX_L_
1008HQ-47NX_L_
1008HQ-56NX_L_
1008HQ-68NX_L_
1008HQ-82NX_L_
1008HQ-R10X_L_
Inductance3
(nH)
3.0 @ 50 MHz
4.1 @ 50 MHz
7.8 @ 50 MHz
10 @ 50 MHz
12 @ 50 MHz
18 @ 50 MHz
22 @ 50 MHz
33 @ 50 MHz
36 @ 50 MHz
39 @ 50 MHz
47 @ 50 MHz
56 @ 50 MHz
68 @ 50 MHz
82 @ 50 MHz
100 @ 50 MHz
Percent SRF min6 DCR max7 Irms8
tolerance4
Q min5
(GHz) (Ohms) (A)
5
5
5
5,2
5,2
5,2,1
5,2
5,2
5,2
5,2
5,2,1
5,2,1
5,2,1
5,2
5,2
70 @ 1500 MHz
75 @ 1500 MHz
75 @ 500 MHz
60 @ 500 MHz
70 @ 500 MHz
62 @ 350 MHz
62 @ 350 MHz
75 @ 350 MHz
65 @ 350 MHz
75 @ 350 MHz
75 @ 350 MHz
75 @ 350 MHz
80 @ 350 MHz
80 @ 350 MHz
62 @ 350 MHz
8.10
6.20
3.80
3.60
2.80
2.70
2.05
1.70
1.40
1.30
1.45
1.23
1.15
1.06
0.82
0.04
0.05
0.05
0.06
0.06
0.07
0.07
0.09
0.09
0.09
0.12
0.12
0.13
0.16
0.16
1.6
1.6
1.6
1.6
1.5
1.4
1.4
1.3
1.3
1.3
1.2
1.2
1.1
1.1
1.0
1. When ordering, specify tolerance, termination and packaging codes:
1008HQ-R10XGLC
Tolerance: F = 1%  G = 2%  J = 5%
(Table shows stock tolerances in bold.)
Termination: L = RoHS compliant silver-palladium-platinum-glass frit.
Special order: T = RoHS tin-silver-copper
(95.5/4/0.5) or S = non-RoHS tin-lead (63/37).
Packaging: C = 7machine-ready reel. EIA-481 embossed plastic
tape (2000 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter C instead.
D = 13machine-ready reel. EIA-481 embossed plastic
tape Factory order only, not stocked (7500 parts
per full reel).
2. Part is wound on low profile coilform.
3. Inductance measured using a Coilcraft SMD-A fixture in an Agilent/
HP 4286A impedance analyzer with Coilcraft-provided correlation
pieces.
4. Tolerances in bold are stocked for immediate shipment.
5. Q measured using an Agilent/HP 4291A with an Agilent/HP 16193 test
fixture.
6. For SRF less than 6 GHz, measured using an Agilent/HP 8753D network
analyzer and a Coilcraft SMD-D test fixture. For SRF greater than
6 GHz, measured using an Agilent/HP 8722ES network analyzer and a
Coilcraft SMD­‑D test fixture.
7. DCR measured on a Cambridge Technology micro-ohmmeter and a
Coilcraft CCF840 test fixture.
8. Current that causes a 15°C temperature rise from 25°C ambient.
9. Electrical specifications at 25°C.
For part marking data, visit http://www.coilcraft.com/colrcode.cfm.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Core material Ceramic
Terminations  RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
Weight  32.4 – 35.7 mg;   17.1 – 17.7 mg (Low profile parts)
Ambient temperature  –40°C to +125°C with Irms current, +125°C
to +140°C with derated current
Storage temperature  Component: –40°C to +140°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL)  +25 to +125 ppm/°C
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
One per billion hours / one billion hours, calculated per Telcordia SR-332
Packaging  2000/7reel; 7500/13reel
Standard height parts:  Plastic tape:  8 mm wide, 0.23 mm thick,
4 mm pocket spacing, 1.8 mm pocket depth
Low profile parts:  Plastic tape:  8 mm wide, 0.3 mm thick,
4 mm pocket spacing, 1.6 mm pocket depth
PCB washing  Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Document 190-1  Revised 02/23/15



Coilcraft
Coilcraft

1008HQ-68NXJLC Datasheet Preview

1008HQ-68NXJLC Datasheet

Chip Inductors

No Preview Available !

1008HQ-68NXJLC pdf
Document 190-2
Chip Inductors – 1008HQ Series (2520)
Typical Q vs Frequency
Typical L vs Frequency
120
110
100
90
80
70
60
50
40
30
20
10
0
10
68 nH
47 nH
22 nH
10 nH
3.0 nH
100 nH
100 1000
Frequency (MHz)
10000
120
110
100
90
80
70
60
50
40
30
20
10
0
1
100 nH
68 nH
47 nH
22 nH
10 nH
3.0 nH
10
100
1000
10000
Frequency (MHz)
Irms Derating
120
110
100
90
80
70
60
50
40
30
20
10
0
-40
-20
0 20 40 60 80 100 120 140
Ambient temperature (°C)
B
overall
F
AG
C
Pick and
place
material
I
J
H
E
terminal
F
D
Terminal wraparound:
approx 0.015/0,38 both ends
I
Recommended
Land Pattern
A B C D
max max   max* ref E F G H I J
0.115 0.110 0.080 0.020 0.080 0.020 0.060 0.100 0.040 0.050 inches
2,92 2,79 2,03 0,51 2,03 0,51 1,52 2,54 1,02 1,27 mm
* Low profile parts: 0.050/1,27
Height dimension (C) is before optional solder application. For maximum
height dimension including solder, add 0.006 in / 0,152 mm.
Document 190-2  Revised 02/23/15


Part Number 1008HQ-68NXJLC
Description Chip Inductors
Maker Coilcraft
Total Page 2 Pages
PDF Download
1008HQ-68NXJLC pdf
Download PDF File


Buy Electronic Components




Related Datasheet

1 1008HQ-68NXJLB Chip Inductors Coilcraft
Coilcraft
1008HQ-68NXJLB pdf
2 1008HQ-68NXJLC Chip Inductors Coilcraft
Coilcraft
1008HQ-68NXJLC pdf






Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

site map

webmaste! click here

contact us

Buy Components