http://www.datasheet4u.com

900,000+ Datasheet PDF Search and Download

Datasheet4U offers most rated semiconductors datasheets pdf




Honeywell International Electronic Components Datasheet

SS5 Datasheet

(SS5 Series) Surface Mount Sensors

No Preview Available !

SS5 pdf
www.DataSheet4U.com
Hall Effect Products
Surface Mount Sensors
SS5 Series
FEATURES/BENEFITS
Wide temperature and
voltage ranges for design
flexibility and harsh
(automotive)environments.
Temperature compensated
for consistent operation with
low-cost magnets (SS500).
SS5 Package is resistant to
thermal and mechanical
stress.
SS5 profile is lower than
other SOT-89 packages.
This allows the customer to
reduce the total gap.
Industry standard "gull-wing"
design. Less susceptibility to
"solder bridging". Allows
increased circuit board
density.
Bipolar, unipolar and latching
magnetics.
Low Gauss versions
available for high accuracy
or wide gap applications.
SS5 package allows 4-pin
package designs
TYPICAL APPLICATIONS
Brushless DC motors
Digital current sensor
Anti-skid braking sensor
Piston detection in hydraulic
cylinder
Valve position sensing
Cam, lever, shaft position
sensing
Tachometer, counter pickup
Push-button sensor
Disk speed, tape rotation,
flow rate sensing
Speed sensing - rate, under,
over speed
Remote reading sensor
Magnetic card reader
SS5 Series Hall effect position sensors are operated by the magnetic
field from a permanent magnet or electromagnet. The small SOT89 style
package surface mounts on PC boards and flexible circuits. The SS5 uses
a industry standard "gull-wing" design which makes it less susceptible to
"solder bridging" and allows increased circuit board density. The SS5
series package can accommodate larger IC’s than SS1 and allows for four-
pin designs
The integrated circuits are designed to provide predictable performance
over the full temperature range of -40 to +150°C. Bipolar, unipolar and
latching magnetics are available. The SS5 has the same footprint and pin-
out as the industry standard SOT-89. It will replace Honeywell SS1 Series
and any equivalent SOT-89 sensors from other suppliers with minimum or
no design changes.
On-board regulation provides extremely stable operation over the full
supply voltage range of 4.5 to 24 VDC(SS51T) or 3.8 to 30 VDC(SS500).
Current consumption is a low 10 mA maximum at 40°C and is typically
7mA or less at room temperature and above. SS5 sensors are capable of
continuous 20 mA sinking output, and can withstand temporary current as
high as 20 mA maximum (SS51T) or 50 mA maximum (SS500). They can
use existing power supply sources in most applications, and can be directly
interfaced with many electronic components without buffering or
compensation circuitry.
SS5 Series sensors are supplied on tape and reel for high-volume,
automated pick and place equipment. Each reel contains 1,000 sensors.
MICRO SWITCH supplies bar and ring magnets for operating Hall effect
sensors. Bar magnets can operate any Hall effect sensor. Ring magnets
are magnetized on the outside diameter with alternating North and South
poles. They are particularly useful with bipolar sensors and rpm
measurement.
MICRO SWITCH Sensing and Control


Honeywell International Electronic Components Datasheet

SS5 Datasheet

(SS5 Series) Surface Mount Sensors

No Preview Available !

SS5 pdf
Hall Effect Products
Surface Mount Sensors
SS5 Series
WIRING DIAGRAMS
ABSOLUTE MAXIMUM RATINGS
Catalog Listing
Supply Voltage
SS51T
-28 to +28 VDC
SS500
-1 to +30 VDC
Voltage externally
applied to output
+28 VDC max. (OFF
condition only)
+30 VDC max. (OFF
condition only)
-0.5 VDC min. (OFF or ON
condition)
Output ON Current 20 mA max.
50 mA max.
Temperature Limits
Operating -40 to +150°C (-40 to
+302°F)
-50 to +160°C (-46 to
+320°F)
Storage -40 to +150°C (-40 to
+302°F)
-65 to +160°C (-54 to
+320°F
Magnetic Flux
No limit. Circuit cannot be
damaged by magnetic
overdrive.
No limit. Circuit cannot be
damaged by magnetic
overdrive.
Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent
damage to the device. This is a stress rating only and functional operation of the device at
these or any other conditions above those indicated in the operations section for extended
periods of time may affect reliability.
OPERATING CHARACTERISTICS
SS51T
Supply Voltage
Current Consumption (Ioff)
Output Voltage (operated)
4.5 to 24 VDC
10 mA
0.4 V
Output Current (operated)
Output Leakage Current
Output Switching Time
Rise, 10 to 90%
Fall, 90 to 10%
Operating Temperature; °C
20 mA
10 µA
1.5 µs
1.5 µs
-40 to +150°C
SS500
3.8 to 30 VDC
10 mA
0.4 V
20mA
10µA
1.5 µs
1.5 µs
-40 to +150°C
Remarks
Max over temp
Sinking 20 mA
max.
VCC = 12 V,
RL = 1.6 K Ohm,
CL = 20 pF
2 Honeywell MICRO SWITCH Sensing and Control
For application help: call 1-800-537-6945


Part Number SS5
Description (SS5 Series) Surface Mount Sensors
Maker HONEYWELL
Total Page 4 Pages
PDF Download
SS5 pdf
Download PDF File


Buy Electronic Components




Related Datasheet

1 SS-01-xx (SS Series) Basic Switch Omron
Omron
SS-01-xx pdf
2 SS-01GLxx (SS Series) Basic Switch Omron
Omron
SS-01GLxx pdf
3 SS-10GLxx (SS Series) Basic Switch Omron
Omron
SS-10GLxx pdf
4 SS-12 Slide Switch Single Port ETC
ETC
SS-12 pdf
5 SS-120 AC Socket Ronnex
Ronnex
SS-120 pdf
6 SS-12E01 Switches ETC
ETC
SS-12E01 pdf
7 SS-12E01 Switches Suntan
Suntan
SS-12E01 pdf
8 SS-12E01-G(B)5-00 Switches LAMB
LAMB
SS-12E01-G(B)5-00 pdf
9 SS-12E01-G2.1 Switches ETC
ETC
SS-12E01-G2.1 pdf






Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

site map

webmaste! click here

contact us

Buy Components