http://www.datasheet4u.com

900,000+ Datasheet PDF Search and Download

Datasheet4U offers most rated semiconductors datasheets pdf




Motorola Electronic Components Datasheet

MOC2R60 Datasheet

OPTOISOLATOR 2 AMPS RANDOM-PHASE TRIAC OUTPUT 600 VOLTS

No Preview Available !

MOC2R60 pdf
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Order this document
by MOC2R60–10/D
Advance Information
POWER OPTOIsolator
2 Amp RandomĆPhase Triac Output
MOC2R60-10*
MOC2R60-15
This device consists of a gallium arsenide infrared emitting diode optically coupled
to a random phase triac driver circuit and a power triac. It is capable of driving a load
of up to 2 amps (rms) directly, on line voltages from 20 to 280 volts AC (rms).
Provides Normally Open Solid State AC Output with 2 Amp Rating
70 Amp Single Cycle Surge Capability
Phase Controllable
High Input-Output Isolation of 3750 vac (rms)
Static dv/dt Rating of 400 Volts/µs Guaranteed
2 Amp Pilot Duty Rating Per UL508 W117 (Overload Test)
and W118 (Endurance Test)
[File No. 129224]
CSA Approved [File No. CA77170-1]. VDE Approval in Process.
Exceeds NEMA 2-230 and IEEE472 Noise Immunity Test Requirements
(See Figure 17)
DEVICE RATINGS (TA = 25°C unless otherwise noted)
Rating
Symbol
Value
Unit
INPUT LED
*Motorola Preferred Devices
OPTOISOLATOR
2 AMPS
RANDOM–PHASE
TRIAC OUTPUT
600 VOLTS
CASE 417-02
79
Style 2
PLASTIC PACKAGE
23
Forward Current — Maximum Continuous
Forward Current — Maximum Peak
(PW = 100µs, 120 pps)
Reverse Voltage — Maximum
OUTPUT TRIAC
IF
IF(pk)
VR
50 mA
1.0 A
CASE 417A-02
Style 1
6.0 V PLASTIC PACKAGE
Output Terminal Voltage — Maximum Transient (1)
Operating Voltage Range — Maximum Continuous
(f = 47 – 63 Hz)
On-State Current Range
(Free Air, Power Factor 0.3)
VDRM
VT
IT(rms)
600
20 to 280
V(pk)
Vac(rms)
0.03 to 2.0
A
CASE 417B-01
Style 1
PLASTIC PACKAGE
Non-Repetitive Single Cycle Surge Current —
Maximum Peak (t = 16.7 ms)
Main Terminal Fusing Current (t = 8.3 ms)
ITSM
I2T
70 A
26 A2sec
DEVICE SCHEMATIC
Load Power Factor Range
Junction Temperature Range
TOTAL DEVICE
Input-Output Isolation Voltage — Maximum (2)
47 – 63 Hz, 1 sec Duration
PF
TJ
VISO
0.3 to 1.0
– 40 to 125
°C
3750
Vac(rms)
3
2
7
Thermal Resistance — Power Triac Junction to
Case (See Figure 18)
Ambient Operating Temperature Range
Storage Temperature Range
Lead Soldering Temperature — Maximum
(1/16From Case, 10 sec Duration)
RθJC
Toper
Tstg
TL
8.0 °C/W
– 40 to +100
– 40 to +150
260
°C
°C
°C
9
1, 4, 5, 6, 8. NO PIN
2. LED CATHODE
3. LED ANODE
7. MAIN TERMINAL 2
9. MAIN TERMINAL 1
1. Test voltages must be applied within dv/dt rating.
2. Input-Output isolation voltage, VISO, is an internal device dielectric breakdown rating.
(2)For this test, pins 2, 3 and the heat tab are common, and pins 7 and 9 are common.
POWER OPTO is a trademark of Motorola, Inc.
This document contains information on a new product. Specifications and information herein are subject to change without notice.
Preferred devices are Motorola recommended choices for future use and best overall value.
REV 1
© MMoototroorlao,lIancO. 1p9t9o5electronics Device Data
1


Motorola Electronic Components Datasheet

MOC2R60 Datasheet

OPTOISOLATOR 2 AMPS RANDOM-PHASE TRIAC OUTPUT 600 VOLTS

No Preview Available !

MOC2R60 pdf
MOC2R60-10 MOC2R60-15
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted)
Characteristic
Symbol
Min
Typ
Max Unit
INPUT LED
Forward Voltage (IF = 10 mA)
Reverse Leakage Current (VR = 6.0 V)
Capacitance
VF 1.00 1.17 1.50
V
IR — 1.0 100 µA
C — 18 — pF
OUTPUT TRIAC
Off-State Leakage, Either Direction
(IF = 0, VDRM = 400 V)
Critical Rate of Rise of Off-State Voltage (Static)
(Vin = 400 vac(pk)) (1) (2)
Holding Current, Either Direction (IF = 0, VD = 12 V, IT = 200 mA)
COUPLED
IDRM(1)
0.25 100
µA
dv/dt(s)
400
— V/µs
IH — 10 — mA
LED Trigger Current Required to Latch Output
MOC2R60-10 IFT(on)
7.0
10
mA
Either Direction (Main Terminal Voltage = 2.0 V) (3) (4) MOC2R60-15
12 15
On-State Voltage, Either Direction (IF = Rated IFT(on), ITM = 2.0 A)
Commutating dv/dt (Rated VDRM, IT = 30 mA – 2.0 A(rms),
TA = – 40 + 100°C, f = 60 Hz) (2)
Common-mode Input-Output dv/dt (2)
Input-Output Capacitance (V = 0, f = 1.0 MHz)
Isolation Resistance (VI-O = 500 V)
VTM
dv/dt (c)
dv/dt(cm)
CISO
RISO
5.0
1012
0.96
40,000
1.3
1014
1.3
V
V/µS
V/µS
pF
1. Per EIA/NARM standard RS–443, with VP = 200 V, which is the instantaneous peak of the maximum operating voltage.
2. Additional dv/dt information, including test methods, can be found in Motorola applications note AN1048/D.
3. All devices are guaranteed to trigger at an IF value less than or equal to the max IFT. Therefore, the recommended operating IF lies between
3. the device’s maximum IFT(on) limit and the Maximum Rating of 50 mA.
4. Current–limiting resistor required in series with LED.
TYPICAL CHARACTERISTICS
100
80
60
40
20
0
– 40 – 20
0 20 40 60 80
TA, AMBIENT TEMPERATURE (°C)
100 120
Figure 1. Maximum Allowable Forward LED
Current versus Ambient Temperature
2.00
Pulse Only
Pulse or DC
1.80
1.60
1.40
1.20 TA = – 40°C
1.00
0.80
1
25°C
100°C
10 100
IF, FORWARD CURRENT (mA)
Figure 2. LED Forward Voltage
versus LED Forward Current
1000
2 Motorola Optoelectronics Device Data


Part Number MOC2R60
Description OPTOISOLATOR 2 AMPS RANDOM-PHASE TRIAC OUTPUT 600 VOLTS
Maker Motorola
Total Page 8 Pages
PDF Download
MOC2R60 pdf
Download PDF File
MOC2R60 pdf
View for Mobile



Buy Electronic Components




Related Datasheet

1 MOC2R60 OPTOISOLATOR 2 AMPS RANDOM-PHASE TRIAC OUTPUT 600 VOLTS Motorola
Motorola
MOC2R60 pdf






Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

site map

webmaste! click here

contact us

Buy Components