http://www.datasheet4u.com

900,000+ Datasheet PDF Search and Download

Datasheet4U offers most rated semiconductors datasheets pdf





TEMIC Semiconductors
TEMIC Semiconductors

U2403B Datasheet Preview

U2403B Datasheet

Charge Timer

No Preview Available !

U2403B pdf
Charge Timer
U2403B
Description
The U2403B is a monolithic, integrated-bipolar circuit
which can be used in applications for time-controlled,
constant-current charge. Selection of charge current
versus timing is carried out by using the external circuit
at Pins 2, 3 and 4. For high current requirement, an
external transistor is recommended in series with the
battery. To protect the IC against high power loss
(typically > 140°C), the oscillator is shut down when the
reference voltage is switched off (0 V). The latter also
takes place when there is a saturation caused by collector
voltage at Pin 1. When the overtemperature has
disappeared and the collector voltage at Pin 1 has
exceeded the supply voltage (V1 > VS), charge time
operation continues (see flow chart in figure 3).
Features
D Easy-to-run autonomous dual rate charger
D Constant charge current
D 3 h – 24 h charge time programmable
D Low cost dc regulator
D Overtemperature protection
D Charge-mode indication
D Operation starts at the moment of battery insertion
D Fast charge time-test mode
Applications
D Cordless telephones
D Low-cost battery-charge timer
D Entertainment
Package: DIP8, SO8
Block Diagram
Power
supply
AC/DC
Battery
inserted
LED2
Charge
R1
R5
LED
LED1
Ready
8
C1
VS GND
67
94 8629
Charge mode
indicator
Power supply
VS = 3.5 to 12 V
Test
mode
5 STM
í max
140°C
1
V1
í
2
Shunt
Timer and control logic
VRef = 1.5 V/ 0.1 V/ 0 V
VRef
+
RC
oscillator
3
Sense
4
Osc
R3 R4
C4
Figure 1. Block diagram with external circuit
TELEFUNKEN Semiconductors
Rev. A2, 14–Nov–96
1 (12)



TEMIC Semiconductors
TEMIC Semiconductors

U2403B Datasheet Preview

U2403B Datasheet

Charge Timer

No Preview Available !

U2403B pdf
U2403B
Pin Description
V1 1
V2 2
Sense 3
Osc 4
8 LED
7 GND
6 VS
5 STM
Pin Symbol
Function
1 V1 Collector terminal
2 V2 Shunt emitter terminal
3 V3 Amplifier sense input
4 Osc Oscillator input
5 STM Test mode switch
6 VS Supply voltage
7 GND Reference point, GND
8 LED Charge mode indicator
94 8685
Pin 1, Collector Voltage V1
Pin 1 is an open collector output. When V1 3 V, the
charge cycle is switched off until it is above the supply
voltage, as shown in figure 6.
Pin 2, Shunt Emitter
123
Pin 4 Oscillator
256
Pulse
The constant current source is supplied by the internal
operational amplifier. The voltage across R3 is deter-
mined via the internal reference source.
Ich = V3/R3 (V3 = Vsense)
Pin 3, Amplifier Sense Input (Inverted)
Pin 5 Test – Mode
94 8839
Figure 2. Quick test timer 1/3
The voltage-regulated current source has a closed loop at
Pin 2, Pin 3, and resistor R3.
Pin 4, Oscillator Input R4, C4
Selection of current charge versus timing is carried out by
using the external circuit at Pins 2, 3, and 4. Typical
values are given in charge characteristics (see table next
page).
Pin 5, Test-Mode Switch for Charging Time
The charging time, tch, is given by the following equation.
+tch
1
fosc
2n
where:
fosc = oscillator frequency (see figure 2)
n = frequency divider
= 26, if STM open
= 17, if STM = GND
= 8, if STM = VS
The first eight divider stages can be tested directly.
256 input tact signals at Pin 4 create one tact signal at
Pin 5.
Example
Assume a charge time of 6 h.
Select the values of R4 and C4 from the tables next page.
For example:
WR4 = 470 k
C4 = 680 pF
There is a frequency of approximately 3100 Hz at Pin 4.
It is possible to test the charge time of 6 h by running
through the charge cycle for a very short time. By
connecting Pin 5 with GND, the test time is 42 s. By
connecting Pin 5 with Pin 1 (V1), the test time is reduced
to about 82.4 ms. R5 is connected in parallel to the LED2
and provides a protective bypass function for the LED
(see figure 1).
Pin 6, Supply Voltage, VS
[VS 3.1 V power-on reset release (turn-on)
[VS 2.9 V under-voltage reset
[VS 13 V supply voltage limitation
Pin 7, Ground
2 (12)
TELEFUNKEN Semiconductors
Rev. A1, 20-Mar-96


Part Number U2403B
Description Charge Timer
Maker TEMIC Semiconductors
Total Page 12 Pages
PDF Download
U2403B pdf
Download PDF File
U2403B pdf
View for Mobile






Related Datasheet

1 U2403B Charge Timer TEMIC Semiconductors
TEMIC Semiconductors
U2403B pdf




Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

site map

webmaste! click here

contact us

Buy Components