900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Atmel Electronic Components Datasheet

45DB642D Datasheet

AT45DB642D

No Preview Available !

Features
Single 2.7V - 3.6V Supply
Dual-interface Architecture
– RapidS Serial Interface: 66 MHz Maximum Clock Frequency
SPI Compatible Modes 0 and 3
– Rapid8 8-bit Interface: 50 MHz Maximum Clock Frequency
User Configurable Page Size
– 1024 Bytes per Page
– 1056 Bytes per Page
– Page Size Can Be Factory Pre-configured for 1024 Bytes
Page Program Operation
– Intelligent Programming Operation
– 8192 Pages (1024/1056 Bytes/Page) Main Memory
Flexible Erase Options
– Page Erase (1 Kbyte)
– Block Erase (8 Kbytes)
– Sector Erase (256 Kbytes)
– Chip Erase (64 Mbits)
Two SRAM Data Buffers (1024/1056 Bytes)
– Allows Receiving of Data while Reprogramming the Flash Array
Continuous Read Capability through Entire Array
– Ideal for Code Shadowing Applications
Low-power Dissipation
– 10 mA Active Read Current Typical – Serial Interface
– 10 mA Active Read Current Typical – 8-bit Interface
– 25 µA Standby Current Typical
– 15 µA Deep Power Down Typical
Hardware and Software Data Protection Features
– Individual Sector
Permanent Sector Lockdown for Secure Code and Data Storage
– Individual Sector
Security: 128-byte Security Register
– 64-byte User Programmable Space
– Unique 64-byte Device Identifier
JEDEC Standard Manufacturer and Device ID Read
100,000 Program/Erase Cycles Per Page Minimum
Data Retention – 20 Years
Green (Pb/Halide-free/RoHS Compliant) Packaging Options
Temperature Range
– Industrial: -40°C to +85°C
64-megabit
2.7-volt
Dual-interface
DataFlash®
AT45DB642D
3542K–DFLASH–04/09


Atmel Electronic Components Datasheet

45DB642D Datasheet

AT45DB642D

No Preview Available !

1. Description
The AT45DB642D is a 2.7-volt, dual-interface sequential access Flash memory ideally suited for
a wide variety of digital voice-, image-, program code- and data-storage applications. The
AT45DB642D supports RapidS serial interface and Rapid8 8-bit interface. RapidS serial inter-
face is SPI compatible for frequencies up to 66 MHz. The dual-interface allows a dedicated
serial interface to be connected to a DSP and a dedicated 8-bit interface to be connected to a
microcontroller or vice versa. However, the use of either interface is purely optional. Its
69,206,016 bits of memory are organized as 8,192 pages of 1,024 bytes (binary page size) or
1,056 bytes (standard DataFlash page size) each. In addition to the main memory, the
AT45DB642D also contains two SRAM buffers of 1,024 (binary buffer size) bytes/1,056 bytes
(standard DataFlash buffer size) each. The buffers allow receiving of data while a page in the
main Memory is being reprogrammed, as well as writing a continuous data stream. EEPROM
emulation (bit or byte alterability) is easily handled with a self-contained three step read-modify-
write operation. Unlike conventional Flash memories that are accessed randomly with multiple
address lines and a parallel interface, the DataFlash uses either a RapidS serial interface or a
8-bit Rapid8 interface to sequentially access its data. The simple sequential access dramatically
reduces active pin count, facilitates hardware layout, increases system reliability, minimizes
switching noise, and reduces package size. The device is optimized for use in many commercial
and industrial applications where high-density, low-pin count, low-voltage and low-power are
essential.
To allow for simple in-system reprogrammability, the AT45DB642D does not require high input
voltages for programming. The device operates from a single power supply, 2.7V to 3.6V, for
both the program and read operations. The AT45DB642D is enabled through the chip select pin
(CS) and accessed via a three-wire interface consisting of the Serial Input (SI), Serial Output
(SO), and the Serial Clock (SCK), or an 8-bit interface consisting of the input/output pins (I/O7 -
I/O0) and the clock pin (CLK).
All programming and erase cycles are self-timed.
2 AT45DB642D
3542K–DFLASH–04/09


Part Number 45DB642D
Description AT45DB642D
Maker ATMEL Corporation
PDF Download

45DB642D Datasheet PDF






Similar Datasheet

1 45DB642D AT45DB642D
ATMEL Corporation





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z



Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy