CAT34RC02
ABSOLUTE MAXIMUM RATINGS*
Temperature Under Bias .................. -55°C to +125°C
Storage Temperature ........................ -65°C to +150°C
Voltage on Any Pin with
Respect to Ground(1) ............ -2.0 V to VCC + 2.0 V
Voltage on A0 .................................................. -2.0 V to +12.0 V
VCC with Respect to VSS .............................. -2.0 V to +7.0 V
*COMMENT
Stresses above those listed under “Absolute Maximum Ratings” may
cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions
outside of those listed in the operational sections of this specification is not
implied. Exposure to any absolute maximum rating for extended periods
may affect device performance and reliability.
RELIABILITY CHARACTERISTICS
Symbol
Parameter
Reference Test Method
NEND(2)(*)
Endurance
TDR(2)(*) Data Retention
VZAP(2)(*) ESD Susceptibility
ILTH(2)(3)
Latch-up
MIL-STD-883, Test Method 1033
MIL-STD-883, Test Method 1008
MIL-STD-883, Test Method 3015
JEDEC Standard 17
(*) Page Mode, VCC = 5 V, 25°C
D.C. OPERATING CHARACTERISTICS
VCC = 1.7 V to 5.5 V, unless otherwise specified.
Min
1,000,000
100
4000
100
Units
Program/ Erase Cycles
Years
Volts
mA
Symbol
Parameter
Test Conditions
Min
Typ
Max Units
ICC
Power Supply Current (Read)
fSCL = 100 kHz
1 mA
ICC
ISB(4)
Power Supply Current (Write)
Standby Current (VCC = 5.0 V)
fSCL = 100 kHz
VIN = GND or VCC
3 mA
1 µA
ILI
Input Leakage Current
VIN = GND to VCC
1 µA
ILO
Output Leakage Current
VOUT = GND to VCC
1 µA
VIL Input Low Voltage
–1
VCC x 0.3
V
VIH Input High Voltage
VCC x 0.7
VCC + 1.0 V
VOL1 Output Low Voltage (VCC = 3.0 V)
IOL = 3 mA
0.4 V
VOL2 Output Low Voltage (VCC = 1.7 V) IOL = 1.5 mA
0.5 V
VHV
RSWP Set/Clear Overdrive
VHV - VCC > 4.8 V
A0 High Voltage
7
10 V
CAPACITANCE TA = 25°C, f = 400 kHz, VCC = 5 V
Symbol
Test
Conditions
Min Typ
Max Units
CI/O(2)
CIN(2)
Input/Output Capacitance (SDA)
Input Capacitance (other pins)
VI/O = 0 V
VIN = 0 V
8 pF
6 pF
ZWPL
WP Input Impedance
VIN < 0.5 V
5
70 kΩ
ZWPH
WP Input Impedance
VIN > VCC x 0.7
500
kΩ
Note:
(1) The DC input voltage on any pin should not be lower than -0.5 V or higher than VCC + 0.5 V. During transitions, the voltage on any pin
may undershoot to no less than -2.0 V or overshoot to no more than VCC + 2.0 V, for periods of less than 20 ns. The maximum DC
voltage on address pin A0 is +12.0 V.
(2) This parameter is tested initially and after a design or process change that affects the parameter.
(3) Latch-up protection is provided for stresses up to 100 mA on I/O pins from -1.0 V to VCC + 1.0 V.
(4) Standby Current, ISB = 10 µA max at extended temperature range.
Doc. No. 1052, Rev. K
2
