EZ-PD™ CCG2 Datasheet
USB Type-C Port Controller
USB Type-C Port Controller
General Description
EZ-PD™ CCG2 is a USB Type-C controller that complies with the latest USB Type-C and PD standards. EZ-PD CCG2 provides a
complete USB Type-C and U1SB Power Delivery port control solution for passive cables, active cables, and powered accessories. It
can also be used in many upstream and downstream facing port applications. EZ-PD CCG2 uses Cypress’s proprietary M0S8
technology with a 32-bit, 48-MHz Arm® Cortex®-M0 processor with 32-KB flash and integrates a complete Type-C Transceiver
including the Type-C termination resistors RP, RD and RA.
Applications
Type-C Support
■ USB Type-C EMCA cables
■ USB Type-C powered accessories
■ USB Type-C upstream facing ports
■ USB Type-C downstream facing ports
Features
■ Integrated transceiver (baseband PHY)
■ Integrated UFP (RD), EMCA (RA) termination resistors, and
current sources for DFP (RP)
■ Supports one USB Type-C port
Low-Power Operation
■ 2.7-V to 5.5-V operation
32-bit MCU Subsystem
■ 48-MHz ARM Cortex-M0 CPU
■ 32-KB Flash
■ 4-KB SRAM
■ In-system reprogrammable
Integrated Digital Blocks
■ Integrated timers and counters to meet response times
required by the USB-PD protocol
■ Run-time reconfigurable serial communication block (SCB)
with reconfigurable I2C, SPI, or UART functionality
Clocks and Oscillators
■ Integrated oscillator eliminating the need for external clock
■ Two independent VCONN rails with integrated isolation
between the two
■ Independent supply voltage pin for GPIO that allows 1.71-V to
5.5-V signaling on the I/Os
■ Reset: 1.0 µA, Deep Sleep: 2.5 µA, Sleep: 2.0 mA
System-Level ESD on CC and VCONN Pins
■ ± 8-kV Contact Discharge and ±15-kV Air Gap Discharge based
on IEC61000-4-2 level 4C
Packages
■ 1.63 mm × 2.03 mm, 20-ball wafer-level CSP (WLCSP) with
0.4-mm ball pitch
■ 2.5 mm × 3.5 mm × 0.6 mm 14-pin DFN
■ 4.0 mm × 4.0 mm, 0.55 mm 24-pin QFN
■ Supports industrial (40 °C to +85 °C) and extended industrial
(40 °C to +105 °C) temperature ranges
Logic Block Diagram
CCG2: USB Type-C Cable Controller
MCU Subsystem
Integrated Digital Blocks
TCPWM1
CORTEX-M0
48 MHz
SCB2
(I2C, SPI, UART)
SCB2
(I2C, SPI, UART)
Profiles and
Configurations
I/O Subsystem
CC5
VCONN1
VCONN2
VDDIO
GPIO6
Port
Flash
(32 KB)
SRAM
(4 KB)
Baseband MAC
Baseband PHY
Integrated Rd3, Ra4,
and Rp7
Serial Wire Debug
1 Timer, counter, pulse-width modulation block
2 Serial communication block configurable as UART, SPI, or I2C
3 Termination resistor denoting a UFP
4 Termination resistor denoting an EMCA
5 Configuration Channel
6 General-purpose input/output
7 Current Sources to indicate a DFP
Cypress Semiconductor Corporation • 198 Champion Court
Document Number: 001-93912 Rev. *M
• San Jose, CA 95134-1709 • 408-943-2600
Revised July 11, 2018