900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Cypress Semiconductor Electronic Components Datasheet

CYBLE-222014-01 Datasheet

EZ-BLE PRoC Module

No Preview Available !

PRELIMINARY
CYBLE-222014-01
EZ-BLE™ PRoC™ Bluetooth 4.2 Module
General Description
The Cypress CYBLE-222014-01 is a fully certified and qualified
module supporting BluetoothLow Energy (BLE) 4.2 wireless
communication. The CYBLE-222014-01 is a turnkey solution
and includes onboard crystal oscillators, chip antenna, passive
components, and Cypress PRoC™ BLE. Refer to the
CYBL10X7X datasheet for additional details on the capabilities
of the PRoC BLE device used on this module.
The CYBLE-222014-01 supports a number of peripheral
functions (ADC, timers, counters, PWM) and serial
communication protocols (I2C, UART, SPI) through its
programmable architecture. The CYBLE-222014-01 includes a
royalty-free BLE stack compatible with Bluetooth 4.2 and
provides up to 16 GPIOs in a small 10 × 10 × 1.80 mm package.
The CYBLE-222014-01 is drop-in compatible with the
CYBLE-022001-00 (128KB BT 4.1) and CYBLE-222005-00
(256KB BT 4.1).
Module Description
Module size: 10.0 mm ×10.0 mm × 1.80 mm (with shield)
256-KB flash memory, 32-KB SRAM memory
Up to 16 GPIOs configurable as open drain high/low,
pull-up/pull-down, HI-Z analog, HI-Z digital, or strong output
Bluetooth 4.2 qualified single-mode module
Certified to FCC, CE MIC, KC, and IC regulations
Eight-channel direct memory access (DMA) controller
32-bit processor (0.9 DMIPS/MHz) with single-cycle 32-bit
multiply, operating at up to 48 MHz
Industrial temperature range: –40 °C to +85 °C
Watchdog timer with dedicated internal low-speed oscillator
(ILO)
Two-pin SWD for programming
Power Consumption
TX output power: –18 dbm to +3 dbm
Received signal strength indicator (RSSI) with 1-dB resolution
TX current consumption of 15.6 mA (radio only, 0 dbm)
RX current consumption of 16.4 mA (radio only)
Low power mode support
Deep Sleep: 1.3 µA with watch crystal oscillator (WCO) on
Hibernate: 150 nA with SRAM retention
Stop: 60 nA with XRES wakeup
Functional Capabilities
Up to 15 capacitive sensors for buttons or sliders with
best-in-class signal-to-noise ration (SNR) and liquid tolerance
12-bit, 1-Msps SAR ADC with internal reference,
sample-and-hold (S/H), and channel sequencer
Two serial communication blocks (SCBs) supporting I2C
(master/slave), SPI (master/slave), or UART
Four dedicated 16-bit timer, counter, or PWM blocks
(TCPWMs)
Programmable low-voltage detect (LVD) from 1.8 V to 4.5 V
I2S master interface
Bluetooth Low Energy protocol stack supporting generic
access profile (GAP) Central, Peripheral, Observer, or
Broadcaster roles
Switches between Central and Peripheral roles on-the-go
Standard Bluetooth Low Energy profiles and services for
interoperability
Custom profile and service for specific use cases
Benefits
The CYBLE-222014-01 module is provided as a turnkey
solution, including all necessary hardware required to use BLE
communication standards.
Proven, qualified, and certified hardware design ready to use
Small footprint (10 × 10 mm × 1.80 mm), perfect for space
constrained applications
Reprogrammable architecture
Fully-certified module eliminates the time needed for design,
development and certification processes
Bluetooth SIG qualified with QDID and Declaration ID
Flexible communication protocol support
PSoC® Creator™ provides an easy-to-use integrated design
environment (IDE) to configure, develop, program, and test a
BLE application
Cypress Semiconductor Corporation
Document Number: 002-11186 Rev. *A
198 Champion Court
San Jose, CA 95134-1709 408-943-2600
Revised March 23, 2016


Cypress Semiconductor Electronic Components Datasheet

CYBLE-222014-01 Datasheet

EZ-BLE PRoC Module

No Preview Available !

PRELIMINARY
CYBLE-222014-01
More Information
Cypress provides a wealth of data at www.cypress.com to help you to select the right module for your design, and to help you to
quickly and effectively integrate the module into your design.
Overview: EZ-BLE Module Portfolio, Module Roadmap
EZ-BLE PRoC Product Overview
PRoC BLE Silicon Datasheet
Application notes: Cypress offers a number of BLE application
notes covering a broad range of topics, from basic to advanced
level. Recommended application notes for getting started with
EZ-BLE modules are:
AN96841 - Getting Started with EZ-BLE Module
AN94020 - Getting Started with PRoC BLE
AN97060 - PSoC® 4 BLE and PRoC™ BLE - Over-The-Air
(OTA) Device Firmware Upgrade (DFU) Guide
AN91162 - Creating a BLE Custom Profile
AN91184 - PSoC 4 BLE - Designing BLE Applications
AN92584 - Designing for Low Power and Estimating Battery
Life for BLE Applications
AN85951 - PSoC® 4 CapSense® Design Guide
AN95089 - PSoC® 4/PRoC™ BLE Crystal Oscillator Selec-
tion and Tuning Techniques
AN91445 - Antenna Design and RF Layout Guidelines
Knowledge Base Articles
KBA97095 - EZ-BLE™ Module Placement
Technical Reference Manual (TRM):
PRoC® BLE Technical Reference Manual
Development Kits:
CY8CKIT-042-BLE, Bluetooth® Low Energy (BLE) Pioneer
Kit
CY8CKIT-002, PSoC® MiniProg3 Program and Debug Kit
Test and Debug Tools:
CYSmart, Bluetooth® LE Test and Debug Tool (Windows)
CYSmart Mobile, Bluetooth® LE Test and Debug Tool
(Android/iOS Mobile App)
PSoC Creator Integrated Design Environment (IDE)
PSoC Creator is an Integrated Design Environment (IDE) that enables concurrent hardware and firmware editing, compiling and
debugging of PSoC 3, PSoC 4, PSoC 5LP, PSoC 4 BLE, PRoC BLE and EZ-BLE module systems with no code size limitations. PSoC
peripherals are designed using schematic capture and simple graphical user interface (GUI) with over 120 pre-verified,
production-ready PSoC Components™.
PSoC Components are analog and digital “virtual chips,” represented by an icon that users can drag-and-drop into a design and
configure to suit a broad array of application requirements.
Bluetooth Low Energy Component
The Bluetooth Low Energy Component inside PSoC Creator provides a comprehensive GUI-based configuration window that lets you
quickly design BLE applications. The Component incorporates a Bluetooth Core Specification v4.2 compliant BLE protocol stack and
provides API functions to enable user applications to interface with the underlying Bluetooth Low Energy Sub-System (BLESS)
hardware via the stack.
Technical Support
Frequently Asked Questions (FAQs): Learn more about our BLE ECO System.
Forum: See if your question is already answered by fellow developers on the PSoC 4 BLE and PRoC BLE forums.
Visit our support page and create a technical support case or contact a local sales representatives. If you are in the United States,
you can talk to our technical support team by calling our toll-free number: +1-800-541-4736. Select option 2 at the prompt.
Document Number: 002-11186 Rev. *A
Page 2 of 37


Part Number CYBLE-222014-01
Description EZ-BLE PRoC Module
Maker Cypress Semiconductor
Total Page 30 Pages
PDF Download

CYBLE-222014-01 Datasheet PDF

View PDF for Mobile








Similar Datasheet

1 CYBLE-222014-01 EZ-BLE PRoC Module
Cypress Semiconductor





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy