900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Cypress Semiconductor Electronic Components Datasheet

S6E1C32C0A Datasheet

Microcontroller

No Preview Available !

S6E1C3 Series
32-bit ARM® Cortex®-M0+
FM0+ Microcontroller
The S6E1C3 Series is a series of highly integrated 32-bit microcontrollers designed for embedded controllers aiming at low power
consumption and low cost. This series has the ARM Cortex-M0+ Processor with on-chip Flash memory and SRAM, and consists of
peripheral functions such as various timers, ADC and communication interfaces (UART, CSIO (SPI), I2C, I2S, Smart Card, and USB).
The products which are described in this data sheet are placed into TYPE3-M0+ product categories in "FM0+ Family Peripheral
Manual".
Features
32-bit ARM Cortex-M0+ Core
Processor version: r0p1
Maximum operating frequency: 40.8 MHz
Nested Vectored Interrupt Controller (NVIC): 1 NMI
(non-maskable interrupt) and 24 peripheral interrupt with 4
selectable interrupt priority levels
24-bit System timer (Sys Tick): System timer for OS task
management
Bit Band Operation
Compatible with Cortex-M3 bit band operation.
On-Chip Memory
Flash memory
Up to 128 Kbytes
Read cycle: 0 wait-cycle
Security function for code protection
SRAM
The on-chip SRAM of this series has one independent SRAM .
Up to 16 Kbytes
4Kbytes: can retain value in Deep standby Mode
USB Interface
USB interface is composed of Device and Host
With Main PLL, USB clock can be generated by multiplication
of Main clock.
USB Device
USB 2.0 Full-Speed supported
Max 6 EndPoint supported
• EndPoint 0 is control transfer
• EndPoint 1, 2 can be selected Bulk-transfer,
Interrupt-transfer or Isochronous-transfer
• EndPoint 3 to 5 can select Bulk-transfer or
Interrupt-transfer
• EndPoint 1 to 5 comprise Double Buffer
• The size of each EndPoint is according to the follows
• EndPoint 0, 2 to 5 : 64 bytes
• EndPoint 1 : 256 bytes
USB host
USB 2.0 Full/Low-Speed supported
Bulk-transfer, Interrupt-transfer and Isochronous-transfer
support
USB Device connected/disconnected automatically detect
IN/OUT token handshake packet automatically
Max 256-byte packet-length supported
Wake-up function supported
Multi-Function Serial Interface (Max 6channels)
3 channels with 64Byte FIFO (Ch.4, 6 and 7), 3 channels
without FIFO (Ch.0, 1 and 3)
The operation mode of each channel can be selected from
one of the following.
UART
CSIO (CSIO is known to many customers as SPI)
I2C
UART
Full duplex double buffer
Parity can be enabled or disabled.
Built-in dedicated baud rate generator
External clock available as a serial clock
Hardware Flow control* : Automatically control the
transmission by CTS/RTS (only ch.4)
* : S6E1C32B0A/S6E1C31B0A and
S6E1C32C0A/S6E1C31C0A do not support Hardware
Flow control.
Various error detection functions (parity errors, framing
errors, and overrun errors)
CSIO (also known as SPI)
Full duplex double buffer
Built-in dedicated baud rate generator
Overrun error detection function
Serial chip select function (ch1 and ch6 only)
Data length: 5 to 16 bits
I2C
Standard-mode (Max: 100 kbps) supported / Fast-mode
(Max 400 kbps) supported.
I2S (MFS-I2S)
Using CSIO (Max 2 ch: ch.4, ch.6) and I2S clock generator
Supports two transfer protocol
I2S
MSB-justified
Master mode only
Cypress Semiconductor Corporation
Document Number: 002-00233 Rev.*B
• 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600
Revised March 4, 2016


Cypress Semiconductor Electronic Components Datasheet

S6E1C32C0A Datasheet

Microcontroller

No Preview Available !

S6E1C3 Series
I2C Slave
I2C Slave supports the slave function of I2C and wake-up
function from Standby mode.
Descriptor System Data Transfer Controller (DSTC)
(64 Channels)
The DSTC can transfer data at high-speed without going via
the CPU. The DSTC adopts the Descriptor system and,
following the specified contents of the Descriptor that has
already been constructed on the memory, can access directly
the memory / peripheral device and performs the data
transfer operation.
It supports the software activation, the hardware activation,
and the chain activation functions
A/D Converter (Max: 8 Channels)
12-bit A/D Converter
Successive approximation type
Conversion time: 2.0 μs @ 2.7 V to 3.6 V
Priority conversion available (2 levels of priority)
Scan conversion mode
Built-in FIFO for conversion data storage (for scan
conversion: 16 steps, for priority conversion: 4 steps)
Base Timer (Max: 8 Channels)
The operation mode of each channel can be selected from one
of the following.
16-bit PWM timer
16-bit PPG timer
16/32-bit reload timer
16/32-bit PWC timer
General-Purpose I/O Port
This series can use its pin as a general-purpose I/O port when
it is not used for an external bus or a peripheral function. All
ports can be set to fast general-purpose I/O ports or slow
general-purpose I/O ports. In addition, this series has a port
relocate function that can set to which I/O port a peripheral
function can be allocated.
All ports are Fast GPIO which can be accessed by 1cycle
Capable of controlling the pull-up of each pin
Capable of reading pin level directly
Port relocate function
Up to 54 fast general-purpose I/O ports @64-pin package
Certain ports are 5 V tolerant.
See 4.List of Pin Functions and 5.I/O Circuit Typefor the
corresponding pins.
Dual Timer (32-/16-bit Down Counter)
The Dual Timer consists of two programmable 32-/16-bit down
counters. The operation mode of each timer channel can be
selected from one of the following.
Free-running mode
Periodic mode (= Reload mode)
One-shot mode
Real-Time Clock
The Real-time Clock counts
year/month/day/hour/minute/second/day of the week from year
00 to year 99.
The RTC can generate an interrupt at a specific time
(year/month/day/hour/minute/second/day of the week) and
can also generate an interrupt in a specific year, in a specific
month, on a specific day, at a specific hour or at a specific
minute.
It has a timer interrupt function generating an interrupt upon
a specific time or at specific intervals.
It can keep counting while rewriting the time.
It can count leap years automatically.
Watch Counter
The Watch Counter wakes up the microcontroller from the low
power consumption mode. The clock source can be selected
from the main clock, the sub clock, the built-in high-speed CR
clock or the built-in low-speed CR clock.
Interval timer: up to 64 s (sub clock: 32.768 kHz)
External Interrupt Controller Unit
Up to 12 external interrupt input pins
Non-maskable interrupt (NMI) input pin: 1
Watchdog Timer (2 Channels)
The watchdog timer generates an interrupt or a reset when the
counter reaches a time-out value.
This series consists of two different watchdogs, hardware
watchdog and software watchdog.
The hardware watchdog timer is clocked by the built-in
low-speed CR oscillator. Therefore, the hardware watchdog is
active in any low-power consumption modes except RTC, Stop,
Deep standby RTC and Deep standby Stop mode.
CRC (Cyclic Redundancy Check) Accelerator
The CRC accelerator calculates the CRC which has a heavy
software processing load, and achieves a reduction of the
integrity check processing load for reception data and storage.
CCITT CRC16 and IEEE-802.3 CRC32 are supported.
CCITT CRC16 Generator Polynomial: 0x1021
IEEE-802.3 CRC32 Generator Polynomial: 0x04C11DB7
HDMI-CEC/Remote Control Receiver (Up to 2
Channels)
HDMI-CEC transmitter
Header block automatic transmission by judging Signal
free
Generating status interrupt by detecting Arbitration lost
Document Number: 002-00233 Rev.*B
Page 2 of 107


Part Number S6E1C32C0A
Description Microcontroller
Maker Cypress Semiconductor
Total Page 30 Pages
PDF Download

S6E1C32C0A Datasheet PDF

View PDF for Mobile








Similar Datasheet

1 S6E1C32C0A Microcontroller
Cypress Semiconductor





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy