900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Cypress Semiconductor Electronic Components Datasheet

S6E2C3AL0A Datasheet

Microcontroller

No Preview Available !

S6E2C3 Series
32-bit ARM® Cortex®-M4F
FM4 Microcontroller
Devices in the S6E2C3 Series are highly integrated 32-bit microcontrollers with high performance and competitive cost. This
series is based on the ARM Cortex-M4F processor with on-chip flash memory and SRAM. The series has peripherals such as
motor control timers, A/D converters, and communications interfaces (USB, CAN, UART, CSIO (SPI), I2C, LIN). The products that
are described in this data sheet are placed into TYPE3-M4 product categories "FM4 Family Peripheral Manual Main Part
(002-04856)."
Features
32-bit ARM Cortex-M4F Core
Processor version: r0p1
Up to 200 MHz frequency operation
FPU built-in
Support DSP instructions
Memory protection unit (MPU): improves the reliability of an
embedded system
Integrated nested vectored interrupt controller (NVIC): 1 NMI
(non-maskable interrupt) and 128 peripheral interrupts and
16 priority levels
24-bit system timer (Sys Tick): system timer for OS task
management
On-chip Memories
Flash memory
This series is based on two independent on-chip flash
memories.
Up to 2048 Kbytes
Built-in flash accelerator system with 16 Kbytes trace buffer
memory
Read access to flash memory that can be achieved without
wait-cycle up to an operating frequency of 72 MHz. Even at
the operating frequency more than 72 MHz, an equivalent
single cycle access to flash memory can be obtained by
the flash accelerator system.
Security function for code protection
SRAM
This is composed of three independent SRAMs (SRAM0,
SRAM1 and SRAM2). SRAM0 is connected to the I-code bus
or D-code bus of Cortex-M4F core. SRAM1 and SRAM2 are
connected to system bus of Cortex-M4F core.
SRAM0: up to 192 Kbytes
SRAM1: 32 Kbytes
SRAM2: 32 Kbytes
External Bus Interface
Supports SRAM, NOR, NAND flash and SDRAM device
Up to 9 chip selects CS0 to CS8 (CS8 is only for SDRAM)
8-/16-/32-bit data width
Up to 25-bit address bus
Supports address/data multiplexing
Supports external RDY function
Supports scramble function
Possible to set the validity/invalidity of the scramble function
for the external areas 0x6000_0000 to 0xDFFF_FFFF in 4
Mbytes units.
Possible to set two kinds of the scramble key
Note: It is necessary to use the Cypress provided software
library to use the scramble function.
USB Interface (Max two Channels)
The USB interface is composed of a function and a host.
USB function
USB 2.0 Full-speed supported
Max 6 EndPoint supported
EndPoint 0 is control transfer
EndPoint 1, 2 can be selected bulk-transfer,
interrupt-transfer or isochronous-transfer
EndPoint 3 to 5 can select bulk-transfer or
interrupt-transfer
EndPoint 1 to 5 comprise double buffer
The size of each endpoint is as follows.
Endpoint 0, 2 to 5: 64 byte
EndPoint 1: 256 byte
USB host
USB2.0 Full-Speed/Low-Speed supported
Bulk-transfer, interrupt-transfer, and isochronous-transfer
support
USB Device connected/dis-connected automatically detect
IN/OUT token handshake packet automatically
Max 256-byte packet length supported
Wake-up function supported
Cypress Semiconductor Corporation
Document Number: 002-04988 Rev.*A
• 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600
Revised February 5, 2016


Cypress Semiconductor Electronic Components Datasheet

S6E2C3AL0A Datasheet

Microcontroller

No Preview Available !

S6E2C3 Series
Multi-function Serial Interface (Max 16 channels)
Separate 64 byte receive and transmit FIFO buffers for
channels 0 to 7.
Operation mode is selectable for each channel from the
following:
UART
CSIO (SPI)
LIN
I2C
UART
Full-duplex double buffer
Selection with or without parity supported
Built-in dedicated baud rate generator
External clock available as a serial clock
Various error detect functions available (parity errors,
framing errors, and overrun errors)
CSIO (SPI)
Full-duplex double buffer
Built-in dedicated baud rate generator
Overrun error detect function available
Serial chip select function (ch 6 and ch 7 only)
Supports high-speed SPI (ch 4 and ch 6 only)
Data length 5 to 16-bit
LIN
LIN protocol Rev.2.1 supported
Full-duplex double buffer
Master/slave mode supported
LIN break field generation (can change to 13- to 16-bit
length)
LIN break delimiter generation (can change to 1- to 4-bit
length)
Various error detect functions available (parity errors,
framing errors, and overrun errors)
I2C
Standard mode (Max 100 kbps)/Fast mode (Max 400 kbps)
supported
Fast mode Plus (Fm+) (Max 1000 kbps, only for ch 3 = ch A
and ch 7 = ch B) supported
DMA Controller (Eight channels)
DMA controller has an independent bus, so the CPU and
DMA controller can process simultaneously.
Eight independently configured and operated channels
Transfer can be started by software or request from the
built-in peripherals
Transfer address area: 32-bit (4 GB)
Transfer mode: Block transfer/Burst transfer/Demand
transfer
Transfer data type: bytes/half-word/word
Transfer block count: 1 to 16
Number of transfers: 1 to 65536
DSTC (Descriptor System data Transfer Controller;
256 Channels)
The DSTC can transfer data at high-speed without going via
the CPU. The DSTC adopts the descriptor system and,
following the specified contents of the descriptor that has
already been constructed on the memory, can access directly
the memory/peripheral device and perform the data-transfer
operation.
It supports the software activation, the hardware activation,
and the chain activation functions.
A/D Converter (Max 32 channels)
12-bit A/D Converter
Successive approximation type
Built-in three units
Conversion time: 0.5 μs at 5 V
Priority conversion available (priority at two levels)
Scanning conversion mode
Built-in FIFO for conversion data storage (for SCAN
conversion: 16 steps, for priority conversion: 4 steps)
D/A Converter (Max 2 Channels)
R-2R type
12-bit resolution
Base Timer (Max 16 Channels)
Operation mode is selected from the following for each
channel:
16-bit PWM timer
16-bit PPG timer
16-/32-bit reload timer
16-/32-bit PWC timer
General Purpose I/O Port
This series can use its pins as general purpose I/O ports
when they are not used for external bus or peripherals;
moreover, the port relocate function is built in. It can set the
I/O port to which the peripheral function can be allocated.
Capable of pull-up control per pin
Capable of reading pin level directly
Built-in port-relocate function
Up to 120 high-speed general-purpose I/O ports in 144 pin
package
Some pins 5V tolerant I/O.
See 4. Pin Descriptions and 5. I/O Circuit Type for the
corresponding pins.
Document Number: 002-04988 Rev.*A
Page 2 of 198


Part Number S6E2C3AL0A
Description Microcontroller
Maker Cypress Semiconductor
PDF Download

S6E2C3AL0A Datasheet PDF






Similar Datasheet

1 S6E2C3AL0A Microcontroller
Cypress Semiconductor





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z



Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy