datasheet4u.com

900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf





Elantec
Elantec

EL1503C Datasheet Preview

EL1503C Datasheet

High Power Differential Line Driver

No Preview Available !

EL1503C pdf
EL1503C - Product Brief
High Power Differential Line Driver
Features
General Description
• High power ADSL driver
The EL1503C ADSL Line Driver contains two wideband high-voltage
• 39.2VP-P differential output drive
into 22
• 42.4VP-P differential output drive
dinto 65
e• Driver 2nd/3rd harmonics of
d-66dBc/-72dBc at 2VP-P into 100
n -differential
• Supply current of 12.5mA per
e samplifier
m n• Supply current control
m ig• Power saving modes
s C• Standard surface-mount packages
• Ultra-small LPP package
eco De 3AApplications
0• ADSL line drivers
R w 5• HDSL2 line drivers
• Video distribution amplifiers
Not Ne EL1Ordering Information
rPart No.
fo eEL1503CL
sEL1503CL-T7
UEL1503CL-T13
Package
24-Pin LPP
24-Pin LPP
24-Pin LPP
Tape &
Reel
-
7”
13”
Outline #
MDP0046
MDP0046
MDP0046
drivers which are ideally suited for both ADSL and HDSL2 applica-
tions. They can supply a 39.2VP-P signal into a 22load while
exhibiting very low distortion. The EL1503C also has a number of
power saving features. The IADJ pin can be used to set the maximum
supply current and the C0 and C1 pins can be used to digitally vary the
supply current to one of four modes. These modes include full power,
low power, terminate only and power down.
The EL1503C uses current-feedback type amplifiers, which achieve a
high slew rate while consuming moderate power. They retain their fre-
quency response over a wide range of externally set gains. The
EL1503C operates on ±5V to ±12V supplies and consumes only
12.5mA per amplifier.
The device is supplied in a standard form-factor 20-pin SO (0.300"),
16-pin thermal SO (0.150”), and the small footprint (4x5mm) 24-pin
LPP packages. Center pins on each side of the 20-pin and 16-pin pack-
ages are used as ground connections and heat spreaders. The LPP
package has the potential for a low θJA (<40°C/W) and dissipates heat
by means of a thermal pad that is soldered onto the PCB. All package
options are specified for operation over the full -40°C to +85°C tem-
perature range.
Pin Configurations
EL1503CM
20-Pin SO (0.300")
-
MDP0027
NC 1
19 NC
EL1503CM-T13 20-Pin SO (0.300")
13”
MDP0027
EL1503CS
EL1503CS-T7
16-Pin SO (0.150”)
16-Pin SO (0.150”)
-
7”
MDP0027
MDP0027
NC 2
18 NC
EL1503CS-T13 16-Pin SO (0.150”)
13”
MDP0027
VS- 3
17 VS+
NC 4
Thermal Pad
16 NC
NC 5
15 NC
NC 6
14 NC
GND 7
13 GND
24-Pin LPP Top View
Pin Configurations continues on Page 3
Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.
© 2001 Elantec Semiconductor, Inc.



Elantec
Elantec

EL1503C Datasheet Preview

EL1503C Datasheet

High Power Differential Line Driver

No Preview Available !

EL1503C pdf
EL1503C - Product Brief
High Power Differential Line Driver
NoftoRr UeNcseoewmEDmLe1es5ni0gd3neAsdC-
General Disclaimer
Specifications contained in this data sheet are in effect as of the publication date shown. Elantec, Inc. reserves the right to make changes in the cir-
cuitry or specifications contained herein at any time without notice. Elantec, Inc. assumes no responsibility for the use of any circuits described
herein and makes no representations that they are free from patent infringement.
Elantec Semiconductor, Inc.
675 Trade Zone Blvd.
Milpitas, CA 95035
Telephone: (408) 945-1323
(888) ELANTEC
Fax: (408) 945-9305
European Office: +44-118-977-6020
Japan Technical Center: +81-45-682-5820
WARNING - Life Support Policy
Elantec, Inc. products are not authorized for and should not be used
within Life Support Systems without the specific written consent of
Elantec, Inc. Life Support systems are equipment intended to sup-
port or sustain life and whose failure to perform when properly used
in accordance with instructions provided can be reasonably
expected to result in significant personal injury or death. Users con-
templating application of Elantec, Inc. Products in Life Support
Systems are requested to contact Elantec, Inc. factory headquarters
to establish suitable terms & conditions for these applications. Elan-
tec, Inc.’s warranty is limited to replacement of defective
components and does not cover injury to persons or property or
other consequential damages.
2 Printed in U.S.A.


Part Number EL1503C
Description High Power Differential Line Driver
Maker Elantec
Total Page 2 Pages
PDF Download
EL1503C pdf
EL1503C Datasheet PDF
[partsNo] view html
View PDF for Mobile








Similar Datasheet

1 EL1503A High Power Differential Line Driver Intersil Corporation
Intersil Corporation
EL1503A pdf
2 EL1503C High Power Differential Line Driver Elantec
Elantec
EL1503C pdf





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy