900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf






FTDI

FT4232HP Datasheet Preview

FT4232HP Datasheet

High Speed USB Bridge

No Preview Available !

FT4233HP Datasheet
Version 1.1
Document No.: FT_001473 Clearance No.: FTDI#555
Future Technology
Devices International Ltd
FT4233HP / FT4232HP
(High Speed USB Bridge with
Type-C/PD3.0 Controller)
The FT4233HP/FT4232HP is a Hi-Speed USB device
with a Type-C/PD3.0 controller that fully supports
the latest USB Type-C and Power Delivery (PD)
standards enabling support for power negotiation
with the ability to sink or source current to a USB
host device. The USB bridge function delivers 4
independent channels compatible with the existing
FT4232H Quad Hi-speed USB to multipurpose
UART/MPSSE solution.
The FT4233HP/FT4232HP has the following advanced
features:
Supports the PD specification Rev 3.0.
Port 1 mode configuration for Sink or Dual-role.
Port 2 works as Sink, supporting charge through
to Port 1(FT4233HPQ and FT4233HPL only).
Supports 5V3A, 9V3A, 12V3A, 15V3A and 20V3A
PDOs as sink or source.
Type-C/PD Physical Layer Protocol.
PD policy engine using 32-bit RISC controller
with 8kB data RAM and 48kB code ROM.
PD mode configuration through external
EEPROM.
Options to use external MCU controlling PD
policy through I2C interface.
USB to quad serial ports with a variety of
configurations.
Entire USB protocol handled on the chip. No USB
specific firmware programming required.
USB 2.0 High Speed (480Mbits/Second) and Full
Speed (12Mbits/Second) compatible.
Two Multi-Protocol Synchronous Serial Engine
(MPSSE) on channel A and channel B, to simplify
synchronous serial protocol (USB to JTAG, I2C,
SPI or bit-bang) design.
Independent Baud rate generators.
RS232/RS422/RS485 UART Transfer Data Rate
up to 12Mbaud. (RS232 Data Rate limited by
external level shifter).
FTDI’s royalty-free Virtual Com Port (VCP) and
Direct (D2XX) drivers eliminate the requirement
for USB driver development in most cases.
Optional traffic TX/RX indicators can be added
with LEDs and an external 74HC595 shift
register.
Adjustable receive buffer timeout.
Support for USB suspend and resume conditions
via PWREN#, SUSPEND# and RI# pins.
FTDI FT232R/FT-X style, asynchronous serial
UART interface option with full hardware
handshaking and modem interface signals.
Fully assisted hardware or X-On / X-Off software
handshaking.
UART Interface supports 7/8 bit data, 1/2 stop
bits, and Odd/Even/Mark/Space/No Parity.
Enable control for RS485 serial applications using
TXDEN pin through external EEPROM.
Operational configuration mode and USB
Description strings configurable in external
EEPROM over the USB interface.
Low operating and USB suspend current.
Configurable I/O drive strength (4, 8, 12 or
16mA) and slew rate.
USB Bulk data transfer mode (512 byte packets
in High Speed mode).
Dedicated Windows/Linux DLLs available for USB
to SPI, and USB to I2C applications.
+3.3V single supply operating voltage range.
+3.3V I/O interfacing.
Highly integrated design includes +1.2V LDO
regulator for VCORE, integrated POR function
and on chip clock multiplier PLL (12MHz
480MHz).
Extended -40°C to 85°C industrial operating
temperature range.
Available in Pb-free QFN-76/QFN-68/LQFP-80
package (RoHS compliant).
Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in
any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied
on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices
International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights
are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of
the product might reasonably be expected to result in personal injury. This document provides preliminary information that ma y be subject
to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document.
Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH United Kingdom .
Scotland Registered Company Number: SC136640
Copyright © Future Technology Devices International Limited
1




FTDI

FT4232HP Datasheet Preview

FT4232HP Datasheet

High Speed USB Bridge

No Preview Available !

1 Typical Applications
FT4233HP Datasheet
Version 1.1
Document No.: FT_001473 Clearance No.: FTDI#555
USB Bridge with Type-C/PD3.0 (chargers and Numerous combinations of 4 channels.
devices).
Upgrading Legacy Peripheral Designs to USB.
Up to 60W power delivery via USB PD and/or Field Upgradable USB Products.
Type-C port.
Cellular and cordless phone USB data transfer
Get power from USB device functions, e.g.
cables and interfaces.
portable USB host needs charging when USB is Interfacing MCU / PLD / FPGA based designs to
connected.
USB.
Single chip USB to four channels UART (RS232, PDA to USB data transfer.
RS422 or RS485) or Bit-Bang interfaces.
USB Smart Card Readers.
Single chip USB to 2 JTAG channels plus 2 USB Instrumentation.
UARTS.
USB Industrial Control.
Single chip USB to 1 JTAG channel plus 3 USB FLASH Card Reader / Writers.
UARTS.
Set Top Box PC USB interface.
Single chip USB to 1 SPI channel plus 3 UARTS. USB Digital Camera Interface.
Single chip USB to 2 SPI channels plus 2 USB Bar Code Readers.
UARTS.
Single chip USB to 2 Bit-Bang channels plus 2
UARTS.
Single chip USB to 1 SPI channel, plus 1 JTAG
channel plus 2 UARTS.
Single chip USB to 2 I2C channels plus 2
UARTS.
1.1 Driver Support
The FT4233HP/FT4232HP requires USB drivers (listed below), available free from
https://www.ftdichip.com, which are used to make the FT4233HP/FT4232HP appear as a virtual COM port
(VCP). This allows the user to communicate with the USB interface via a standard PC serial emulation port
(for example TTY). Another FTDI USB driver, the D2XX driver, can also be used with application software
to directly access the FT4233HP/FT4232HP through a DLL.
Royalty free VIRTUAL COM PORT
(VCP) DRIVERS for...
Windows 10 32,64-bit
Windows 8/8.1 32,64-bit
Windows 7 32,64-bit
Windows Server 2008 and server 2012 R2
Mac OS-X
Linux 2.4 and greater
Royalty free D2XX Direct Drivers
(USB Drivers + DLL S/W Interface)
Windows 10 32,64-bit
Windows 8/8.1 32,64-bit
Windows 7 32,64-bit
Windows Server 2008 and server 2012 R2
Mac OS-X
Linux 2.4 and greater
Android(J2xx)
For driver installation, please refer to the installation guides on our website:
https://ftdichip.com/document/installation-guides/
The following additional installation guides application notes and technical notes are also available:
AN_113 - Interfacing FT2232H Hi-Speed Devices To I2C Bus
AN_114 - Interfacing FT2232H Hi-Speed Devices To SPI Bus
AN_177 - User Guide For libMPSSE I2C
AN_110 - Programmers Guide for High Speed FTCJTAG DLL
AN_178 - User Guide For libMPSSE - SPI
AN_135 - MPSSE Basics
Copyright © Future Technology Devices International Limited
2


Part Number FT4232HP
Description High Speed USB Bridge
Maker FTDI
PDF Download

FT4232HP Datasheet PDF






Similar Datasheet

1 FT4232H Quad High Speed USB to Multipurpose UART/MPSSE
FTDI
2 FT4232HL Quad High Speed USB to Multipurpose UART/MPSSE
FTDI
3 FT4232HP High Speed USB Bridge
FTDI
4 FT4232HQ Quad High Speed USB to Multipurpose UART/MPSSE
FTDI





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z



Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy