FAIRCHILD e1LA111 eILA311
,uA 111
ELECTRICAL CHARACTERISTICS: Vs = ot15 V, TA = -55·C to +125·C unless otherwise specified, Note 3.
CHARACTER ISTICS
CONDITIONS
MIN
TYP
Input Offset Voltage INote 4)
Input Offset Current INote 4)
Input Bias Current
Voltage Gain
Response Time INote 5)
Saturation Voltage
Strobe On Current
Output Leakage Current
Input Offset Voltage INote 4)
Input Offset Current INote 4)
Input Bias Current
Input Voltage Range
Saturation Voltage
Output Leakage Current
Positive Supply Current
Negative Supply Current
TA = 25°C, RS'; 50 kn
TA = 25°C
T A = 25°C
T A = 25°C
TA - 25°C
VIN .; -5 mY, lOUT - 50 mA
TA = 25°C
TA=25°C
VIN ;> 5 mY, VOUT - 35 V
TA = 25°C
RS'; 50 kn
V+ ;> 4.5 V, V- = 0
VIN .; -6 mY, ISINK'; 8 mA
VIN ;> 5 mY, VOUT = 35 V
TA - 25°C
TA - 25°C
0.7
4.0
60
200
200
0.75
3.0
0.2
±14
0.23
'0.1
5.1
4.1
MAX
3.0
10
100
1.5
10
4.0
20
150
0.4
0.5
6.0
5.0
UNITS
mV
nA
nA
V/mV
ns
V
mA
nA
mV
nA
nA
V
V
}J.A
mA
mA
,uA311
ELECTRICAL CHARACTERISTICS: Vs = ot15 V, TA = O·C to +70°C unless otherwise specified, Note 3.
CH/\R/\CTER!ST!C'S
r.ONDITIONS
I MIN
Input Offset Voltage INote 4)
Input Offset Current INote 4)
Input Bias Current
Voltage Gain
Response Time INote 5)
Saturation Voltage
Strobe On Current
Output Leakage Current
Input Offset Voltage INote 4)
Input Offset Current INote 4)
Jnput 8 ias Current
Input Voltage Range
Saturation Voltage
Positive Supply Current
Negative Supply Current
TA = 25°C, RS'; 50 kn
TA - 25°C
TA = 25°C
TA = 25°C
TA = 25°C
VIN .; -10 mY, lOUT - 50 mA
TA = 25°C
TA - 25°C
VIN;> 10 mY, VOUT - 35 V
TA = 25°C
RS'; 50 kn
y+;> 4.5 V, V -0
VIN'; -10 mY, ISINK'; 8 mA
TA = 25°C
TA = 25°C
TYP
2.0
6.0
100
200
200
0.75
3.0
0.2
±14
0.23
5.1
4.1
MAX
7.5
50
250
1.5
50
10
70
300
0.4
7.5
5.0
UNITS
mV
nA
nA
V/mV
ns
V
mA
nA
mV
nA
nA
V
V
mA
mA
NOTES:
1. This rating applies for ± 15 V supplies. The positive input voltage limit is 30 V above the negative supply. The negative input voltage limit is
equal to the negative supply voltage or 30 V below the positive supply, whichever is less.
2. Rating applies to ambient temperatures up to 70°C. Above 70°C ambient derate linearly at 6.3 mW/oC for metal can; 8.3 mW/oC for
mini DIP.
3. The offset voltage, offset current and bias current specifications apply for any supply voltage from a single 5 V supply up to ±15 V supplies.
4. The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with a
1 mA load. Thus, these parameters define an error band and take into account the worst case effects of voltage gain and input impedance.
5. The response time specified (see definitions) is for a 100 mV input step with 5 mV overdrive.
•
6-9
