900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Integrated Device Technology Electronic Components Datasheet

NW6006-XS Datasheet

ENHANCED TYPE II CALLER ID DECODER WITH STUTTER DIAL TONE DETECTOR

No Preview Available !

ENHANCED TYPE II CALLER ID DECODER
WITH STUTTER DIAL TONE DETECTOR
NW6006
FEATURES
1200 baud Bell 202 and ITU-T V.23 Frequency Shift Keying
(FSK) Demodulation
Stutter dial tone detection
Compliant with following specifications:
Bellcore GR-30-CORE & SR-TSV-002476
TIA/EIA-716, TIA/EIA-777 Draft
TIA/EIA PN-4195 Draft
British Telecom (BT) SIN227 & SIN242
ETSI ETS 300 778-1 and -2
Bellcore “CPE Alerting Signal (CAS)”, British Telecom “Idle State
and Loop State Tone Alert Signal” and ETSI “Dual Tone Alerting
Signal (DT-AS)” detection
Two seperate OP amps with adjustable gain for Tip/Ring and
Telephone Hybrid connections
Monitoring of the stop bit for framing error check
Serial FSK data interface with selectable output of bit stream or 1
byte buffer
FSK carrier detection
3 V or 5 V operation
Low power CMOS with intelligent powerdown mode
Operating temperature range: -40 °C to +85 °C
Packages available:
NW6006-XS 20 pin SOIC
(where ‘X’ is the revision ID)
DESCRIPTION
The NW6006 device is a single-chip, 3/5 Volt CMOS caller ID with
call waiting detection circuit. It can receive signals following Bellcore
GR-30-CORE & SR-TSV-002476, BT SIN227 & SIN242, and ETSI
ETS 300 788-1/-2 specifications.
The NW6006 provides 1200 baud Bell 202 and ITU-T V.23 FSK
demodulation, detection in stutter dial tone mode and CAS/DT-AS
detection. Two seperate differential input amplifiers allow the device to
be connected with both Tip/Ring and Telephone Hybrid receive pair.
FSK demodulation is implemented only on Tip/Ring, while DT-AS(or
CAS) detection can be on either Tip/Ring or Hybrid Receive. In
addition, NW6006 provides a serial FSK data interface via which the
data can be selected to be processed as a bit stream or extracted
from a 1 byte built-in buffer. An on-chip Stutter Dial Tone Detector is
provided to support the voice mail applications.
The device can be used in feature or cordless phones with voice
mail for BT Calling Line Identity Presentation (CLIP), CCA CLIP and
Bellcore Calling Identity Delivery (CID) systems. It can also be used in
caller ID boxes, modem, fax machines, answering machines,
database query systems and Computer Telephony Integration (CTI)
systems.
FUNCTIONAL BLOCK DIAGRAM
OSCOUT OSCIN
CB0 CB1 CB2
VREF
IN1+
IN1-
GS1
IN2+
IN2-
GS2
Oscillator
Bias
Generator
PWDN
GS1EN
+
-
+
-
GS2EN
Control Bit Decoder
SDTEN
PWDN FSKEN GS1EN
CASEN MODE
GS2EN
Tone Alert
Detector
CASEN
FSK
Demodulator
FSKEN
Figure 1. Block Diagram
SDTEN
Stutter Dial Tone
Detector
Guard Time
Data/Timing Recovery
MODE
ST/GT
DR/STD
EST
CD/STRDT
DCLK
DATA
The IDT logo is a registered trademark of Integrated Device Technology, Inc
INDUSTRIAL TEMPERATURE RANGE
©2002 Integrated Device Technology, Inc.
JULY 2002
DSC-6049/3


Integrated Device Technology Electronic Components Datasheet

NW6006-XS Datasheet

ENHANCED TYPE II CALLER ID DECODER WITH STUTTER DIAL TONE DETECTOR

No Preview Available !

NW6006 ENHANCED TYPE II CALLER ID DECODER
WITH STUTTER DIAL TONE DETECTOR
PIN INFORMATION
VREF
IN1+
IN1-
GS1
GND
OSCIN
OSCOUT
CB0
DCLK
DATA
1
2
3
4
5
6
7
8
9
10
INDUSTRIAL TEMPERATURE RANGE
20 IN2+
19 IN2-
18 GS2
17 CB2
16 CB1
15 VCC
14 CD/STRDT
13 ST/GT
12 EST
11 DR/STD
Figure 2. Pin Assignment
Name
VREF
IN1+
IN1-
GS1
GND
OSCIN
OSCOUT
CB0
DCLK
DATA
Type Pin No.
Description
O
1
Reference Voltage.
This output is used to bias the input OP amp. It is typically VCC/2.
I 2 Non-inverting Input of the gain adjustable Tip/Ring OP amp.
I 3 Inverting Input of the gain adjustable Tip/Ring OP amp.
Gain Select Output of the gain adjustable Tip/Ring OP amp.
O
4
The Tip/Ring signal can be attenuated or amplified at GS1 by adjusting the feedback resistor between GS1 and IN1-.
The FSK signal is always detected by Tip/Ring OP amp while DT-AS(CAS) signal can be detected by either Tip/Ring
or Hybrid OP amp. The OP amp selection is controlled by CB1 and CB2 bits.
- 5 Ground.
Oscillator Input.
I 6 A 3.579545 MHz crystal or ceramic resonator should be connected between this pin and the OSCOUT. It can also
be driven by an external clock source.
Oscillator Output.
O 7 A 3.579545 MHz crystal or ceramic resonator should be connected between this pin and the OSCIN. When an
external clock drives OSCIN, this pin can be left floating.
Control Bit 0 (FSK Data Interface Mode Select).
I
8
This pin can select the 3-wire FSK data interface mode. A ‘0’ on this pin indicates interface mode 0; while a ‘1’ on
this pin indicates interface mode 1. (The FSK data interface is consisted of DATA, DCLK and DR/STD pins.)
When CB0 is high and CB1, CB2 are both low, the device is set into the power down state.
Data Clock of the Serial FSK Interface.
I/NC 9 In mode 0 (CB0 is low), this pin is unused; In mode 1 (CB0 is high), this pin is an input which clock the FSK data
byte out to the DATA pin.
Data Output of the Serial FSK Interface.
In mode 0 (CB0 is low), the FSK serial bit stream is output to the DATA pin directly.
O 10 In mode 1 (CB0 is high), the start bit is stripped off, the data byte and the stop bit is stored in a 9-bit buffer. At the
end of each word signaled by the DR/STD pin, the microcontroller should shift the byte out onto the DATA pin by
applying 8 read pulses to the DCLK pin. A 9th DCLK pulse will shift out the stop bit for framing error checking.
2


Part Number NW6006-XS
Description ENHANCED TYPE II CALLER ID DECODER WITH STUTTER DIAL TONE DETECTOR
Maker Integrated Device Technology
Total Page 22 Pages
PDF Download

NW6006-XS Datasheet PDF

View PDF for Mobile








Similar Datasheet

1 NW6006-XS ENHANCED TYPE II CALLER ID DECODER WITH STUTTER DIAL TONE DETECTOR
Integrated Device Technology





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy