900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




International Rectifier Electronic Components Datasheet

IR2235SPBF Datasheet

3-PHASE BRIDGE DRIVER

No Preview Available !

Data Sheet No. PD60107 revX
IR2133/IR2135(J&S)&(PbF)
IR2233/IR2235(J&S)&(PbF)
3-PHASE BRIDGE DRIVER
Features
Floating channel designed for bootstrap operation
Fully operational to +600V or+1200V
Tolerant to negative transient voltage
dV/dt immune
Gate drive supply range from 10V/12V to 20V DC and
up to 25V for transient
Undervoltage lockout for all channels
Over-current shut down turns off all six drivers
Independent 3 half-bridge drivers
Matched propagation delay for all channels
2.5V logic compatible
Outputs out of phase with inputs
All parts are also available LEAD-FREE
Product Summary
VOFFSET
IO+/-
VOUT
ton/off (typ.)
Deadtime (typ.)
600V or 1200V max.
200 mA / 420 mA
10 - 20V or 12 - 20V
750/700 ns
250 ns
Packages
Description
The IR2133IR2135/IR2233IR2355 (J&S) are high voltage, high speed
power MOSFET and IGBT driver with three independent high side and
low side referenced output channels for 3-phase applications. Propri-
etary HVIC technology enables ruggedized monolithic construction.
Logic inputs are compatible with CMOS or LSTTL outputs, down to
28-Lead SOIC
28-Lead PDIP
2.5V logic. An independent operational amplifier provides an analog
feedback of bridge current via an external current sense resistor. A
44-Lead PLCC w/o 12 leads
current trip function which terminates all six outputs can also be de-
rived from this resistor. A shutdown function is available to terminate all six outputs. An open drain FAULT signal is provided to
indicate that an over-current or undervoltage shutdown has occurred. Fault conditions are cleared with the FLT-CLR lead. The
output drivers feature a high pulse current buffer stage designed for minimum driver cross-conduction. Propagation delays are
matched to simplify use in high frequency applications. The floating channels can be used to drive N-channel power MOSFETs or
IGBTs in the high side configuration which operates up to 600 volts or 1200 volts.
Typical Connection
up to 600V or 1200V
(Refer to Lead Assignments for correct pin configuration). This/These diagram(s) show electrical connections only.
Please refer to our Application Notes and DesignTips for proper circuit board layout.
www.irf.com
1


International Rectifier Electronic Components Datasheet

IR2235SPBF Datasheet

3-PHASE BRIDGE DRIVER

No Preview Available !

IR2133/IR2135/IR2233/IR2235(J&S)&(PbF)
Absolute Maximum Ratings
Absolute Maximum Ratings indicate sustained limits beyond which damage to the device may occur. All volt-
age parameters are absolute voltages referenced to COM. The Thermal Resistance and Power Dissipation
ratings are measured under board mounted and still air conditions.
Symbol Definition
Min.
Max.
Units
VB1,2,3
VS1,2,3
VHO1,2,3
VCC
VSS
VLO1,2,3
VIN
High side floating supply voltage (IR2133/IR2135)
(IR2233/IR2235)
High side floating supply offset voltage
High side floating output voltage
Fixed supply voltage
Logic ground
Low side output voltage
Logic input voltage (HIN, LIN, ITRIP, SD & FLT-CLR)
-0.3
-0.3
VB1,2,3 - 25
VS1,2,3 - 0.3
-0.3
VCC - 25
-0.3
VSS - 0.3
VIN,AMP Op amp input voltage (CA+ & CA-)
VOUT,AMP Op amp output voltage (CAO)
VFLT
FAULT output voltage
dVS/dt Allowable offset supply voltage transient
PD Package power dissipation @ TA 25ºC (28 Lead PDIP)
(28 Lead SOIC)
(44 lead PLCC)
RthJA Thermal resistance, junction to ambient (28 Lead PDIP)
(28 Lead SOIC)
(44 lead PLCC)
TJ Junction temperature
TS Storage temperature
TL Lead temperature (soldering, 10 seconds
VSS - 0.3
VSS - 0.3
VSS - 0.3
-55
625
1225
VB1,2,3 + 0.3
VB1,2,3 + 0.3
25
VCC + 0.3
VCC + 0.3
(VSS + 15) or
(VCC + 0.3)
whichever is
lower
VCC + 0.3
VCC + 0.3
VCC + 0.3
50
1.5
1.6
2.0
83
78
63
125
150
300
V
V/ns
W
ºC/W
ºC
Recommended Operating Conditions
The input/output logic timing diagram is shown in figure 1. For proper operation the device should be used within the
recommended conditions. All voltage parameters are absolute voltages referenced to COM. The VS offset rating is
tested with all supplies biased at 15V differential.
Symbol Parameter Definition
Min.
Max.
Units
VB1,2,3
High side floating supply voltage
VS1,2,3 + 10/12 VS1,2,3 + 20
VS1,2,3
High side floating supply offset voltage (IR2133/IR2135)
Note 1
600
(IR2233/IR2235) Note 1
1200
VHO1,2,3 High side floating output voltage
VS1,2,3
VB1,2,3
VCC Fixed supply voltage
10 or 12
20
VSS
VLO1,2,3
Low side driver return
Low side output voltage
-5 5
0 VCC
V
VIN Logic input voltage (HIN, LIN, ITRIP, SD & FLT-CLR) VSS VSS + 5
VIN,AMP Op amp input voltage (CA+ & CA-)
VSS VSS + 5
VOUT,AMP Op amp output voltage (CAO)
VFLT FAULT output voltage
VSS VSS + 5
VSS
VCC
Note 1: Logic operational for VS of COM - 5V to COM + 600V/1200V. Logic state held for VS of COM -5V to COM -VBS. (Please refer to the Design Tip
DT97-3 for more details).
Note 2: All input pins, op amp input and output pins are internally clamped with a 5.2V zener diode.
2 www.irf.com


Part Number IR2235SPBF
Description 3-PHASE BRIDGE DRIVER
Maker International Rectifier
PDF Download

IR2235SPBF Datasheet PDF






Similar Datasheet

1 IR2235SPBF 3-PHASE BRIDGE DRIVER
International Rectifier





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z



Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy