900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Intersil Electronic Components Datasheet

6534CV Datasheet

ISL6534CV

No Preview Available !

®
Data Sheet
December 21, 2004
ISL6534
FN9134.1
Dual PWM with Linear
The ISL6534 is a versatile triple regulator that has two
independent synchronous-rectified buck controllers with
integrated 12V gate drivers (OUT1 and OUT2) and a linear
controller (OUT3) to offer precision regulation of up to three
voltage rails. An optional shunt regulator allows 12V only
operation, when a 5V supply is not available.
Each controller has independent soft-start and enable
www.DataShefuent4cUti.ocnoms combined on a single pin. A capacitor from each
SS/EN pin to ground sets the soft-start time, and pulling
SS/EN below 1.0V disables the controller. The SS/EN pins
can be controlled independently or they can be ganged
together to provide complete control of start-up coordination.
The PGOOD function indicates when all regulators have
completed their soft start and provides an indication of short-
circuit conditions on either switching regulator.
There are two ways to control the switching frequency of the
PWM regulators. The default switching frequency is 300kHz
(FS_SYNC pin open). A resistor from FS_SYNC to ground
increases the switching frequency (up to 1MHz). Connecting
the gate signal from another PWM IC synchronizes the
ISL6534 switchers to the frequency of the other controller.
This allows independent regulators operating at a common
frequency to avoid low-frequency beats. The gate drivers for
DDR mode can be staggered by 90° in order to minimize
cross-conduction.
Switcher OUT1 has an internal 0.8% accurate reference for
regulating any voltage down to 0.6V. OUT2 has current
sinking capability and an external reference input allowing
convenient connection to OUT1 through a resistor divider for
DDRAM applications. The 3.3V reference pin provides the
option for independent regulation of OUT2. The linear
controller drives an external N-Channel MOSFET, making
the ISL6534 one of the most versatile regulators available.
Simplified Block Diagram
SS1/EN1
COMP1
FB1
SS2/EN2
REFIN
FB2
COMP2
VREF
SS3/EN3
FB3
OUT1
PWM CONTROLLER
OUT2
PWM CONTROLLER
3.3V
OUT3
LINEAR CONTROLLER
BOOT1
UGATE1
LGATE1
BOOT2
UGATE2
LGATE2
REFOUT
PGOOD
FS/SYNC
DRIVE3
Features
• Two Synchronous-Rectified Buck Controllers
- Voltage Mode control
- VIN range up to 12V
- VOUT range from 0.6V to 6V
- 12V LGATE drivers; up to 12V Boot Strap for UGATE
• Switcher References
- 0.6V Reference for OUT1 (0.8% Accurate)
- 3.3V Reference Output for OUT2 (0.8% Accurate)
- External Reference Input for OUT2
- Buffered VTT Reference Output
• Switcher clocking
- Phase options for Optimal Clock Relationship
- Resistor-Selectable Switching Frequency (300kHz
default; Resistor to Ground for 300kHz to 1MHz range)
- Synchronization-Capable Switching Frequency
(Connect FS_SYNC to Separate Regulator)
• Single Linear Controller
- Drives N-Channel MOSFET
- 0.6V Reference (0.8% Accurate)
- VIN range up to 12V
- VOUT range from 0.6V to 6V
• 12V and 5V supplies required (but optional shunt regulator
can generate VCC = 5.8V from 12V)
• Three Independent Soft-Start/Enable Pins
- Gang Together or Control Independently
• PGOOD Output Indicates All Outputs Available
• Thermally Enhanced QFN or TSSOP Package
• QFN Package:
- Compliant to JEDEC PUB95 MO-220
QFN - Quad Flat No Leads - Package Outline
- Near Chip Scale Package footprint, which improves
PCB efficiency and has a thinner profile
• Pb-Free Available (RoHS Compliant)
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2004. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.


Intersil Electronic Components Datasheet

6534CV Datasheet

ISL6534CV

No Preview Available !

ISL6534
Ordering Information
TEMP.
PART NUMBER (°C)
PACKAGE
PKG. DWG.
#
ISL6534CV
0 to 70 24 Ld EPTSSOP
(exposed pad)
M24.173B
ISL6534CVZ
(See Note)
0 to 70 24 Ld EPTSSOP
M24.173B
(exposed pad) (Pb-free)
ISL6534CR
0 to 70 32 Ld 5x5 QFN
L32.5x5
ISL6534CRZ
(See Note)
0 to 70 32 Ld 5x5 QFN
(Pb-free)
L32.5x5
NOTE: Intersil Pb-free products employ special Pb-free material
www.DataSheseett4sU; m.coolmding compounds/die attach materials and 100% matte tin
plate termination finish, which are RoHS compliant and compatible
with both SnPb and Pb-free soldering operations. Intersil Pb-free
products are MSL classified at Pb-free peak reflow temperatures that
meet or exceed the Pb-free requirements of IPC/JEDEC J STD-
020C.
Add “-T” suffix for tape and reel.
Pinouts (see Pin Descriptions, page 9)
2 FN9134.1


Part Number 6534CV
Description ISL6534CV
Maker Intersil Corporation
PDF Download

6534CV Datasheet PDF






Similar Datasheet

1 6534CV ISL6534CV
Intersil Corporation





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z



Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy