900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Maxim Integrated Semiconductor Electronic Components Datasheet

MAX7370 Datasheet

8 x 8 Key-Switch Controller and LED Driver/GPIOs

No Preview Available !

EVALUATION KIT AVAILABLE
MAX7370
8 x 8 Key-Switch Controller and LED Driver/GPIOs
with I2C Interface and High Level of ESD Protection
General Description
Features
The MAX7370 I2C-interfaced peripheral provides micro-
processors with management of up to 64 key switches,
with optional GPIO and PWM-controlled LED drivers.
The key-switch drivers interface with metallic or resistive
switches with on-resistances up to 5kI. Key inputs are
monitored statically, not dynamically, to ensure low-EMI
operation. The IC features autosleep and autowake
modes to further minimize the power consumption of
the device. The autosleep feature puts the device in a
low-power state (1µA typ) after a timeout period. The
autowake feature configures the device to return to
normal operating mode from sleep upon a keypress.
The key controller debounces and maintains a FIFO
buffer of keypress and release events (including auto-
repeat, if enabled). An interrupt (INT) output can be
configured to alert keypresses, as they occur, or at the
maximum rate.
The same index rows and columns in the device can be
used as a direct logic-level translator.
If the device is not used for key-switch control, all
keyboard pins can be used as GPIOs. Each GPIO can
be programmed to one of the two externally applied
logic voltage levels. Four column ports (COL7–COL4)
can also be configured as LED drivers that feature
constant-current and PWM intensity control. The maximum
constant-current level for each open-drain LED port is
20mA. The intensity of the LED on each open-drain port
can be individually adjusted through a 256-step PWM
control.
The device is offered in a 24-pin (3.5mm x 3.5mm) TQFN
package with an exposed pad, and small 25-bump
(2.159mm x 2.159mm) wafer-level package (WLP) for
cell phones, pocket PCs, and other portable consumer
electronic applications.
The device operates over the -40°C to +85°C extended
temperature range.
Applications
Cell Phones
Notebooks
PDAs
Handheld Games
Portable Consumer Electronics
For related parts and recommended products to use with this part,
refer to www.maximintegrated.com/MAX7370.related.
S Monitors Up to 64 Keys
S Integrated High-ESD Protection
±8kV IEC 61000-4-2 Contact Discharge
±15kV IEC 61000-4-2 Air-Gap Discharge
S Keyscan Uses Static Matrix Monitoring for
Low-EMI Operation
S Four LED Driver Pins on COL7–COL4
S 5V Tolerant, Open-Drain I/O Ports Capable of
Constant-Current LED Drive
S 256-Step PWM Individual LED Intensity-Control
Accuracy
S Individual LED Blink Rates and Common LED
Fade In/Out Rates from 256ms to 4096ms
S FIFO Queues Up to 16 Debounced Key Events
S User-Configurable Keypress and Release
Debounce Time (2ms to 32ms)
S Key-Switch Interrupt (INT) on Each Debounced
Event/FIFO Level, or End-of-Definable Time Period
S 1.62V to 3.6V Operating Supply Voltage
S Individually Programmable GPIOs to Two Logic
Levels
S 8-Channel Individual Programmable Level
Translators
S Provides Optional GPIOs on all ROW_ and COL_
Pins
S Supports Hot Insertion
S 400kbps, 5.5V Tolerant I2C Serial Interface with
Selectable Bus Timeout
Ordering Information appears at end of data sheet.
Typical Operating Circuit
+1.8V
VCC
+2.6V
VLA
+5V
MAX7370 COL4
INT
MCU SDA
SCL
COL5
COL6
COL7
I/O
I/O
AD0 ROW[0:7] 8
GND COL[0:3] 4
32 KEYS
For pricing, delivery, and ordering information, please contact Maxim Direct
at 1-888-629-4642, or visit Maxim’s website at www.maximintegrated.com.
19-5950; Rev 2; 5/15


Maxim Integrated Semiconductor Electronic Components Datasheet

MAX7370 Datasheet

8 x 8 Key-Switch Controller and LED Driver/GPIOs

No Preview Available !

MAX7370
8 x 8 Key-Switch Controller and LED Driver/GPIOs
with I2C Interface and High Level of ESD Protection
ABSOLUTE MAXIMUM RATINGS
VCC, VLA to GND.....................................................-0.3V to +4V
COL3–COL0, ROW7–ROW0 to GND........ -0.3V to (VCC + 0.3V)
COL7–COL4 to GND................................................-0.3V to +6V
SDA, SCL, AD0, INT to GND...................................-0.3V to +6V
VLA to VCC............................................................-0.3V to +2.3V
DC Current on COL7–COL4 to GND..................................25mA
DC Current on COL3–COL0, ROW7–ROW0 to GND............7mA
VCC, VLA, GND Current......................................................80mA
DC Current VCC, VLA to COL3–COL0, ROW7–ROW0..........5mA
Continuous Power Dissipation (TA = +70°C)
24-Pin TQFN (derate 15.4mW/°C above +70°C).......1229mW
25-Bump WLP (derate 19.2mW/°C above +70°C).......850mW
Operating Temperature Range........................... -40°C to +85°C
Junction Temperature......................................................+150°C
Storage Temperature Range............................. -65°C to +150°C
Lead Temperature (TQFN) (soldering, 10s)....................+300°C
Soldering Temperature (reflow).......................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional opera-
tion of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
PACKAGE THERMAL CHARACTERISTICS (Note 1)
24 TQFN
Junction-to-Ambient Thermal Resistance (BJA)..........65.1°C/W
Junction-to-Case Thermal Resistance (BJC).................5.4°C/W
25 WLP
Junction-to-Ambient Thermal Resistance (BJA)............52°C/W
Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer
board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial.
ELECTRICAL CHARACTERISTICS
(VCC = 1.62V to 3.6V, TA = -40NC to +85NC, unless otherwise noted. Typical values are at VCC = 3.3V, TA = +25NC.) (Notes 2, 3)
PARAMETER
Operating Supply Voltage
Second Logic Supply
Operating Supply Current
SYMBOL
VCC
VLA
ICC
CONDITIONS
All key switches open, oscillator
running
N keys pressed
MIN
1.62
VCC
TYP
3.3
3.3
MAX
3.6
3.6
50 65
50 + 28 O N
UNITS
V
V
FA
Sleep-Mode Supply Current
POR Threshold
KEY-SWITCH SPECIFICATIONS
Key-Switch Source Current
Key-Switch Source Voltage
Key-Switch Resistance
Startup Time from Sleep
GPIO SPECIFICATIONS
External Supply Voltage
COL7–COL4 (LED Drivers)
LED Port-to-Port Sink Current Variation
ISL
VPOR
Not using GPO or LED configuration
IKEY
VKEY
RKEY
tSTART
(Note 4)
VLED
VCC = 3.3V, VOL = 1V, TA = +25NC,
10mA output mode
1.8
1.2
28
0.45
2
3
40
0.5
5
2.7
FA
V
FA
V
kI
ms
Q1.5
5
Q2.4
V
%
Maxim Integrated
  2


Part Number MAX7370
Description 8 x 8 Key-Switch Controller and LED Driver/GPIOs
Maker Maxim
Total Page 30 Pages
PDF Download

MAX7370 Datasheet PDF

View PDF for Mobile








Similar Datasheet

1 MAX737 -5V /-12V /-15V / and Adjustable Inverting Current-Mode PWM Regulators
Maxim
2 MAX7370 8 x 8 Key-Switch Controller and LED Driver/GPIOs
Maxim
3 MAX7375 3-Pin Silicon Oscillator
Maxim
4 MAX7376 Silicon Oscillator with Reset Output
Maxim
5 MAX7377 Silicon Oscillator
Maxim
6 MAX7378 Silicon Oscillator with Low-Power Frequency Switching and Reset Output
Maxim





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy