900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Maxim Integrated Semiconductor Electronic Components Datasheet

DS9108 Datasheet

Concreat Temperature Monitor

No Preview Available !

www.DataSheet4U.com
www.maxim-ic.com
GENERAL DESCRIPTION
This product is a sealed plastic stick containing three
DS1921G iButtonsÒ. The iButtons are connected in
parallel through metal plates that are spot-welded to
the IO and GND contact, respectively. Two stranded
wires protruding from the top end of the stick allow
for a 1-WireÒ reader/write to make contact to the
iButtons for setup and data retrieval. Electrically, the
product is specified by the DS1921G data sheet, with
the proper scaling (e.g., current ×3, capacitance ×3).
The mechanical and thermal characteristics of the
module are specified in this document.
APPLICATIONS
· Concrete Maturity Monitoring
TYPICAL OPERATING CIRCUIT
VCC
RPUP*
Portable
1-Wire
reader IO
GND
Temperature
Monitor
Red
Black
DS9108
Concrete Temperature
Monitor
FEATURES
§ Three DS1921G networked to monitor temperate
at the top, bottom and center of the stick
§ Connects to 1-Wire reader/writer through color-
coded 18 AWG (1 mm Ø) stranded wires with ½
inch (1.3 cm) stripped ends
§ Electrically compatible to the DS1921G
Thermochron iButton (3 in parallel)
§ Sealed against liquid intrusion
§ Module position information stored in DS1921G
memory
ORDERING INFORMATION
PART
TEMP RANGE PIN-PACKAGE
DS9108-080
-20°C to 65°C
8” (20.3 cm) depth*
DS9108-100
-20°C to 65°C
10” (25.4 cm) depth
DS9108-120
-20°C to 65°C
12” (30.5 cm) depth
DS9108-150
-20°C to 65°C
15” (38.1 cm) depth
Shipped in bulk with the wires bundled with a tie
* Indicates depth of concrete to monitor, actual stick
length is 0.25” (0.6 cm) less then depth
BLOCK DIAGRAM
Stranded wire
Ends twisted
IO
Red
wire
GND
Black
wire
Metal plates welded
to iButtons
U1 U2 U3
DS1921G
#1
TOP
DS1921G
#2
MIDDLE
DS1921G
#3
BOTTOM
Transition wire to
metal plate
* See Application Note 3829 for Rpup resistor size selection.
iButton and 1-Wire are registered trademarks of Dallas
Semiconductor.
Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device
may be simultaneously available through various sales channels. For information about device errata, click here: www.maxim-ic.com/errata.
1 of 3
REV: 091806


Maxim Integrated Semiconductor Electronic Components Datasheet

DS9108 Datasheet

Concreat Temperature Monitor

No Preview Available !

www.DataSheet4U.com
DS9108 Concrete Temperature Module
ABSOLUTE MAXIMUM RATINGS
Voltage Range on Any Pin Relative to Ground
Operating Temperature Range
Storage Temperature Range
See DS1921G Datasheet
-4°F to 149°F (-20°C to +65°C)
See DS1921G Datasheet
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is
not implied. Exposure to the absolute maximum rating conditions for extended periods may affect device.
SPECIFICATIONS
(See DS1921G datasheet, TA = -4°F to 149°F (-20°C to +65°C) (Note 1))
PARAMETER
CONDITIONS
MIN
TYP MAX
Weight
2.5
72
Physical Dimensions
See technical drawing
Wire Length
12.9 13.1
32.8 33.3
Tensile Strength of Wires
10
44.5
Thermal Response Time
(Note 2)
500
UNITS
ounces
grams
inches
cm
lbf
Newton
s
Note 1: Assembled module production tested at 77°F (25°C).
Note 2: Response time in water is the time required for the recorded value to read 63% of the temperature’s real variation.
Material: PVC with PVC cement and E-60NC black Hysol epoxy for wire sealant
PIN DESCRIPTION
PIN NAME
Red Wire
Black Wire
IO
GND
FUNCTION
1-Wire bus interface. Open drain, requires external pull-up resistor.
Ground Reference
iButton LOCATION WITHIN MODULE
Each DS1921G in the DS9108 module contains a memory tag marker to indicate its position in the assembly. The
position mark is a CRC16 validated packet starting on page 15 in the user memory. The memory image for ‘TOP’,
‘MIDDLE’, and ‘BOTTOM’:
Table 1. Memory Tag Description
TAG TYPE
TOP
MIDDLE
BOTTOM
ADDRESS
1E0h–1E3h
CONTENTS
(HEX)
01 54 FA 60
01 4D 3B AA
01 42 7B AE
DESCRIPTION
‘T’ in a CRC validated packet
‘M’ in a CRC validated packet
‘B’ in a CRC validated packet
2 of 3


Part Number DS9108
Description Concreat Temperature Monitor
Maker Maxim Integrated Products
Total Page 3 Pages
PDF Download

DS9108 Datasheet PDF

View PDF for Mobile








Similar Datasheet

1 DS9100 Touch and Hold Probe Stampings
Dallas Semiconducotr
2 DS9101 Multipurpose Clip
Maxim Integrated
3 DS9104 Digital Decoder Ring
Dallas Semiconducotr
4 DS9105 iButton Number Set
Dallas Semiconducotr
5 DS9106 Ibutton Halo
Maxim Integrated Products
6 DS9107 iButton Capsule
Maxim Integrated Products
7 DS9108 Concreat Temperature Monitor
Maxim Integrated Products





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy