900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Motorola Electronic Components Datasheet

LM311 Datasheet

HIGH PERFORMANCE VOLTAGE COMPARATORS

No Preview Available !

www.DataSheet4U.com
Highly Flexible Voltage
Comparators
The ability to operate from a single power supply of 5.0 V to 30 V or ±15 V
split supplies, as commonly used with operational amplifiers, makes the
LM211/LM311 a truly versatile comparator. Moreover, the inputs of the
device can be isolated from system ground while the output can drive loads
referenced either to ground, the VCC or the VEE supply. This flexibility makes
it possible to drive DTL, RTL, TTL, or MOS logic. The output can also switch
voltages to 50 V at currents to 50 mA. Thus the LM211/LM311 can be used to
drive relays, lamps or solenoids.
Order this document by LM311/D
LM311
LM211
HIGH PERFORMANCE
VOLTAGE COMPARATORS
SEMICONDUCTOR
TECHNICAL DATA
Typical Comparator Design Configurations
Split Power Supply with Offset Balance
3.0 k VCC
Single Supply
VCC
Inputs
5.0 k
5
2
+
6
3
4
VEE
87
1
RL
Output
Inputs
28
+
7
3
1
VEE 4
RL
Output
Ground–Referred Load
VCC
2
Inputs 3
+8 7
1
4 RL
Output
VEE
Input polarity is reversed when
Gnd pin is used as an output.
Load Referred to Negative Supply
VCC
Inputs
2
+
8
7
31
4 RL
Output
VEE
Input polarity is reversed when
Gnd pin is used as an output.
Load Referred to Positive Supply
Inputs
2
+
3
4
VEE
VCC
8
7
1
RL
Output
Strobe Capability
VCC
Inputs
2+ 8
3
6
4
VEE
7
1
RL
Output
TTL Strobe
1.0 k
8
1
N SUFFIX
PLASTIC PACKAGE
CASE 626
8
1
D SUFFIX
PLASTIC PACKAGE
CASE 751
(SO–8)
PIN CONNECTIONS
Gnd 1
Inputs
2
3
VEE 4
+
8 VCC
7 Output
6 Balance/Strobe
5 Balance
(Top View)
ORDERING INFORMATION
Device
Operating
Temperature Range
Package
LM211D
LM311D
LM311N
TA = 25° to +85°C
TA = 0° to +70°C
SO–8
SO–8
Plastic DIP
MOTOROLA ANALOG IC DEVICE DATA
© Motorola, Inc. 1996
Rev 5
1


Motorola Electronic Components Datasheet

LM311 Datasheet

HIGH PERFORMANCE VOLTAGE COMPARATORS

No Preview Available !

LM311 LM211
MAXIMUM RATINGS (TA = +25°C, unless otherwise noted.)
Rating
Symbol
Total Supply Voltage
Output to Negative Supply Voltage
Ground to Negative Supply Voltage
Input Differential Voltage
Input Voltage (Note 2)
Voltage at Strobe Pin
VCC +VEE
VO –VEE
VEE
VID
Vin
Power Dissipation and Thermal Characteristics
Plastic DIP
Derate Above TA = +25°C
Operating Ambient Temperature Range
Operating Junction Temperature
Storage Temperature Range
PD
1/θJA
TA
TJ(max)
Tstg
LM211
36
50
30
±30
±15
VCC to VCC–5
LM311
36
40
30
±30
±15
VCC to VCC–5
625
5.0
–25 to +85
0 to +70
+150
+150
–65 to +150
–65 to +150
Unit
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
mW
mW/°C
°C
°C
°C
ELECTRICAL CHARACTERISTICS (VCC = +15 V, VEE = –15 V, TA = 25°C, unless otherwise noted [Note 1].)
LM211
LM311
Characteristic
Symbol Min Typ Max Min Typ Max Unit
Input Offset Voltage (Note 3)
RS 50 k, TA = +25°C
RS 50 k, Tlow TA Thigh*
Input Offset Current (Note 3) TA = +25°C
Tlow TA Thigh*
Input Bias Current TA = +25°C
Tlow TA Thigh*
Voltage Gain
Response Time (Note 4)
VIO mV
– 0.7 3.0 – 2.0 7.5
– – 4.0 – – 10
IIO – 1.7 10 – 1.7 50 nA
– – 20 – – 70
IIB
45 100
45 250 nA
– – 150 – – 300
AV
40 200
40 200
– V/mV
– 200 –
– 200 – ns
Saturation Voltage
VID –5.0 mV, IO = 50 mA, TA = 25°C
VID –10 mV, IO = 50 mA, TA = 25°C
VCC 4.5 V, VEE = 0, Tlow TA Thigh*
VID 6 6.0 mV, Isink 8.0 mA
VID 6 10 mV, Isink 8.0 mA
Strobe ”On” Current (Note 5)
Output Leakage Current
VID 5.0 mV, VO= 35 V, TA = 25°C, Istrobe= 3.0 mA
VID 10 mV, VO= 35 V, TA = 25°C, Istrobe= 3.0 mA
VID 5.0 mV, VO= 35 V, Tlow TA Thigh*
Input Voltage Range (Tlow TA Thigh*)
VOL
IS
VICR
– 0.75 1.5
–––
– 0.23 0.4
–––
– 3.0 –
V
–––
– 0.75 1.5
–––
– 0.23 0.4
– 3.0 – mA
–14.5
0.2
0.1
–14.7 to
13.8
10
0.5
+13.0
–14.5
0.2
–14.7 to
13.8
50
+13.0
nA
nA
µA
V
Positive Supply Current
ICC
+2.4
+6.0
+2.4 +7.5 mA
Negative Supply Current
IEE – –1.3 –5.0 – –1.3 –5.0 mA
* Tlow = –25°C for LM211
= 0°C for LM311
Thigh = +85°C for LM211
= +70°C for LM311
NOTES: 1. Offset voltage, offset current and bias current specifications apply for a supply voltage range from a single 5.0 V supply up to ±15 V supplies.
2. This rating applies for ±15 V supplies. The positive input voltage limit is 30 V above the negative supply. The negative input voltage limit is equal to the
negative supply voltage or 30 V below the positive supply, whichever is less.
3. The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with a 1.0 mA load. Thus,
these parameters define an error band and take into account the ”worst case” effects of voltage gain and input impedance.
4. The response time specified is for a 100 mV input step with 5.0 mV overdrive.
5. Do not short the strobe pin to ground; it should be current driven at 3.0 mA to 5.0 mA.
2 MOTOROLA ANALOG IC DEVICE DATA


Part Number LM311
Description HIGH PERFORMANCE VOLTAGE COMPARATORS
Maker Motorola
PDF Download

LM311 Datasheet PDF





Similar Datasheet

1 LM310 Voltage Follower
National Semiconductor
2 LM3100 LM3100 Synchronous 1MHz 1.5A Step-Down Voltage Regulator (Rev. G)
ETCTI
3 LM3100 Voltage Regulator
National Semiconductor
4 LM3102 LM3102/-Q1 Synchronous 1-MHz 2.5-A Step-Down Voltage Regulator (Rev. H)
ETCTI
5 LM3102-Q1 LM3102/-Q1 Synchronous 1-MHz 2.5-A Step-Down Voltage Regulator (Rev. H)
ETCTI
6 LM3103 LM3103 Synchronous 1MHz 0.75A Step-Down Voltage Regulator (Rev. F)
ETCTI
7 LM310UH1-SLA1 Real 4K2K TFT LCD
LG
8 LM311 Single Comparators
ON Semiconductor
9 LM311 Single Comparator
Fairchild Semiconductor





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy