900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Murata Manufacturing Electronic Components Datasheet

GRM39-xX5R Datasheet

(GRMxx Series) Surface Mount Monolithic Chip Capacitors

No Preview Available !

SURFACE MOUNT MONOLITHIC CHIP CAPACITORS
HIGH DIELECTRIC CONSTANT TYPE
GRM36/39/40/42-6/42-2/43-2/44-1 Series
FEATURES
s Miniature size
s No Polarity
s Nickel Barrier Termination Standard – highly resistant to
metal migration
s Uniform dimensions and configuration
s Suitable for reflow soldering
s GRM39, 40 and 42-6 suitable for wave soldering
s Minimum series inductance
s Tape and Reel Packaging
s Bulk Case Packaging available for GRM40 and smaller
s Wide selection of capacitance values and voltages
s Largest production capacity and volume in the world
PART NUMBERING SYSTEM
GRM40 – – – X7R 103 K 050 A D
www.DataSheet4U.com
CAPACITOR
TYPE AND SIZE
See below and
following pages.
3-digit code TEMPERATURE
appears as
CHARACTERISTICS
necessary
X5R
to indicate
X7R
special
Y5V
thickness
requirements.
Please consult
your local sales
office for details.
CAPACITANCE
CAPACITANCE
VALUE
TOLERANCE
Expressed in
X7R/X5R:
picofarads and
K = ±10%
identified by a
M = ±20%
three-digit number. Non-standard
First two digits
J = ±5%
represent significant
figures. Last digit
Y5V: Z = +–8200%
specifies the number
of zeros to follow.
VOLTAGE
Identified by
a three-digit
number.
MARKING
PACKAGING
A = Unmarked
Reel Diameter/
Tape Material
Code
7Paper Tape
D
7Plastic Tape
L
13Paper Tape
J
13Plastic Tape
K
Bulk B
Bulk Cassette
7Paper
2mm pitch
C
Q
See pages 33-36 for labeling
and packaging information.
CHIP DIMENSIONS
Dimensions: mm
e ge
Size
GRM36
GRM39*
GRM40
EIA
Code
0402
0603
0805
L
Length
1.0 ± 0.05
1.6 ± 0.1
2.0 ± 0.1
W
Width
0.5 ± 0.05
0.8 ± 0.1
1.25 ± 0.1
GRM42-6 1206
T
3.2 ± 0.15
3.2 ± 0.2
LW
GRM42-2 1210
3.2 ± 0.3
1.6 ± 0.15
1.6 ± 0.2
2.5 ± 0.2
GRM43-2
GRM44-1
*Bulk case packaging is L = 1.6 ± 0.07, W, T = 0.8 ± 0.07.
1812
2220
4.5 ± 0.4
5.7 ± 0.4
3.2 ± 0.3
5.0 ± 0.4
CHIP TERMINATION DIAGRAMS
Nickel Barrier Layer (Standard)
Ceramic Dielectric
Inner Electrode
GRM Series
Inner Termination (Ag or Ag/Pd or Cu)
Nickel Plated Barrier Layer
Tin Plating*
*Size 0402 – Solder Plated
All products on this page are available as standard through authorized Murata Electronics Distributors.
CG01-I
T
Thickness
0.5 ± 0.05
0.8 ± 0.1
0.6 ± 0.1
0.85 ± 0.1
1.25 ± 0.1
0.85 ± 0.1
1.15 ± 0.1
1.6 ± 0.2
1.15 ± 0.1
1.35 ± 0.15
1.8 ± 0.2
2.5 ± 0.2
2.0 max.
2.0 max.
e (min.)
Termination
0.15 ~ 0.3
0.2 ~ 0.5
0.2 ~ 0.7
g (min.)
Insulation
0.4
0.5
0.7
0.3 ~ 0.8
1.5
0.3 min.
0.3 min.
0.3 min.
1.0
2.0
2.0
13


Murata Manufacturing Electronic Components Datasheet

GRM39-xX5R Datasheet

(GRMxx Series) Surface Mount Monolithic Chip Capacitors

No Preview Available !

SURFACE MOUNT MONOLITHIC CHIP CAPACITORS
HIGH DIELECTRIC CONSTANT TYPE– SPECIFICATION
GRM36/39/40/42-6/42-2/43-2/44-1 Series
GENERAL/ELECTRICAL
Capacitance Change
with Temperature:
X5R: ±15% CX –55°C to +85°C
X7R: ±15% CX –55°C to +125°C
Y5V: +–2822% CX –30°C to +85°C
Capacitance & D.F.
(Frequency & Voltage)
X5R, X7R: 1kHz ±100Hz @ 1.0 ±.2Vrms
Y5V: 1kHz ±100Hz @ 1.0 ±.2Vrms
Dissipation Factor (D.F.)
Min. 25V
X5R 2.5%
X7R 2.5%
Y5V 5.0%
16V 10V 6.3V
3.5% 3.5% 5%
3.5% 3.5% 5%
9.0% 12.5% 12.5%
Insulation
Resistance (I.R.)
Dielectric Strength
(Flash)
Typ. Aging (per Decade)
X5R/X7R
100,000 megohms or 1000 megohms-mfd
(whichever is less)
Y5V
10,000 megohms or 500 megohms–mfd
(whichever is less)
250% of rated voltage for 5 seconds with series
resistor limiting charge current to 50mA max.;
200% for 500V
X5R/X7R 3%
Y5V 7%
MECHANICAL
TEST
Terminal
Adhesion
Deflection
Solderability
TEST METHOD
Glass epoxy board
Unit: mm
Mounting
2n
Capacitor R340
10
Load
Deflection
45 45
Supporter
Capacitance meter
MIL-STD-202
Method 208F
POST TEST LIMITS
< 0603 1.0 lbs.
0805 2.2 lbs.
No evidence of termination peeling
1 mm deflection (Glass epoxy board)
No mechanical damage
Cap., DF, IR meet initial limits
Meets Requirement
For specific details contact factory
ENVIRONMENTAL
www.DataSheet4U.com
TEST
TEST METHOD
Thermal
Shock
(Air to Air)
MIL-STD-202, Method 107, Condition A
Prior to starting Thermal Shock test, capacitors shall be heat treated
(deaged) for one (1) hour at 150°C. Allow capacitors to stabilize at
room temperature for 48 hours prior to taking initial measurements.
Post thermal Shock measurement shall be taken after 48 hours
stabilization.
Humidity,
Steady
State
Maintain the capacitor at 40 ± 2°C and 90 to 95% humidity for
500 ± 12 hours. Remove and let sit for 48 ± 4 hours at room
temperature, then measure.
POST TEST LIMITS
Appearance: No visual damage
C: X5R/X7R = ±12.5%
Y5V = ±30.0%
D.F.: X5R/X7R = 2.5% max. @ 25°C, (3.5% max. @ 25°C for 16V & 10V Series)
(7.5% max. @ 25°C for 6.3V Series)
Y5V = 5.0% max. @ 25°C, (9.0% max. @ 25°C for 16V Series)
(15% max. @ 25°C for 10V & 6.3V Series)
I.R.: X5R/X7R = 100,000Mmin. of 1,000MF (whichever is less)
Y5V = 10,000or 500MF min. (whichever is less)
Appearance: No defects
Capacitance: X5R, X7R within ±12.5%; Z5U, Y5V within ±30%
Q/D.F.: See chart below.
I.R.: 1,000Mor 50F (whichever is less)
Humidity Load
Apply the rated voltage at 40 ± 2°C and 90 to 95% humidity for
500 ± 12 hours. Remove and let sit for 48 ± 4 hours at room
temperature, then measure. The charge/discharge current is
less than 50mA.
• Initial measurement for Y5V/10V max.
Apply the rated DC voltage for 1 hour at 40 ± 20°C.
Remove and let sit for 48 ± 4 hours at room temperature.
Perform initial measurement.
Life Test
14
Apply 200% of rated voltage for 1000 ± 12 hours at
maximum operating temperature; 150% for 500V
Upon completion of above test wait 48 hours prior
to performing post testing.
Appearance: No defects
Capacitance: X5R, X7R within ±12.5%; Z5U within ±30%;
Y5V within +30/-40% (10Vmax), within ±30% (others)
Q/D.F.
Char.
X5R
X7R
Z5U
25V min.
0.05 max.
0.05 max.
Y5V 0.075 max.
16V
0.05 max.
0.1 max. (C<1.0F)
0.125 max.
(C1.0F)
10V 6.3V
0.05 max. 0.075 max.
——
0.15 max. 0.15 max.
I.R.: 500Mor 25F (whichever is less)
Dielectric Strength: No failure
Appearance: No defects
Capacitance: X5R/X7R ± 12.5% CX, Z5U/Y5V ±30% CX
D.F.: X5R/X7R = 3.0% max. @ 25°C, (5% max. @ 25°C for 16V & 10V Series)
(7.5% max. @ 25°C for 6.3V Series)
Y5V = 7.5% max. @ 25°C, (10% max. @ 25°C for 16V Series)
(15% max. @ 25°C for 10V & 6.3V Series)
I.R.: X5R/X7R 1,000Mor 50M-mfd. (whichever is less)
Y5V 1,000Mor 50M-mfd. (whichever is less)
Flash: 250% rated voltage
CG01-I


Part Number GRM39-xX5R
Description (GRMxx Series) Surface Mount Monolithic Chip Capacitors
Maker Murata Electronics
Total Page 4 Pages
PDF Download

GRM39-xX5R Datasheet PDF

View PDF for Mobile








Similar Datasheet

1 GRM39-xX5R (GRMxx Series) Surface Mount Monolithic Chip Capacitors
Murata Electronics





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy