900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




NXP Semiconductors Electronic Components Datasheet

P89LPC938 Datasheet

8-bit microcontroller

No Preview Available !

www.DataSheet4U.com
P89LPC938
8-bit microcontroller with accelerated two-clock 80C51 core
8 kB 3 V byte-erasable Flash with 10-bit A/D converter
Rev. 01 — 25 February 2005
Product data sheet
1. General description
The P89LPC938 is a single-chip microcontroller, available in low cost packages, based on
a high performance processor architecture that executes instructions in two to four clocks,
six times the rate of standard 80C51 devices. Many system-level functions have been
incorporated into the P89LPC938 in order to reduce component count, board space, and
system cost.
2. Features
2.1 Principal features
s 8 kB byte-erasable Flash code memory organized into 1 kB sectors and 64-byte
pages. Single-byte erasing allows any byte(s) to be used as non-volatile data storage.
s 256-byte RAM data memory and a 512-byte auxiliary on-chip RAM.
s 512-byte customer Data EEPROM on chip allows serialization of devices, storage of
set-up parameters, etc.
s 8-input multiplexed 10-bit A/D converter. Two analog comparators with selectable
inputs and reference source.
s Two 16-bit counter/timers (each may be configured to toggle a port output upon timer
overflow or to become a PWM output) and a 23-bit system timer that can also be used
as a RTC.
s Enhanced UART with fractional baud rate generator, break detect, framing error
detection, and automatic address detection; 400 kHz byte-wide I2C-bus
communication port and SPI communication port.
s CCU provides PWM, input capture, and output compare functions.
s High-accuracy internal RC oscillator option allows operation without external oscillator
components. The RC oscillator option is selectable and fine tunable.
s 2.4 V to 3.6 V VDD operating range. I/O pins are 5 V tolerant (may be pulled up or
driven to 5.5 V).
s 28-pin TSSOP, PLCC, and HVQFN packages with 23 I/O pins minimum and up to 26
I/O pins while using on-chip oscillator and reset options.


NXP Semiconductors Electronic Components Datasheet

P89LPC938 Datasheet

8-bit microcontroller

No Preview Available !

Philips Semiconductors
P89LPC938
8-bit microcontroller with 10-bit A/D converter
2.2 Additional features
s A high performance 80C51 CPU provides instruction cycle times of 111 ns to 222 ns
for all instructions except multiply and divide when executing at 18 MHz. This is six
times the performance of the standard 80C51 running at the same clock frequency. A
lower clock frequency for the same performance results in power savings and reduced
EMI.
s Serial Flash ICP allows simple production coding with commercial EPROM
programmers. Flash security bits prevent reading of sensitive application programs.
s Serial Flash ISP allows coding while the device is mounted in the end application.
s In-Application Programming of the Flash code memory. This allows changing the code
in a running application.
s Watchdog timer with separate on-chip oscillator, requiring no external components.
The watchdog prescaler is selectable from eight values.
s Low voltage reset (brownout detect) allows a graceful system shutdown when power
fails. May optionally be configured as an interrupt.
s Idle and two different power-down reduced power modes. Improved wake-up from
Power-down mode (a LOW interrupt input starts execution). Typical power-down
current is 1 µA (total power-down with voltage comparators disabled).
s Active-LOW reset. On-chip power-on reset allows operation without external reset
components. A reset counter and reset glitch suppression circuitry prevent spurious
and incomplete resets. A software reset function is also available.
s Configurable on-chip oscillator with frequency range options selected by user
programmed Flash configuration bits. Oscillator options support frequencies from
20 kHz to the maximum operating frequency of 18 MHz.
s Oscillator fail detect. The watchdog timer has a separate fully on-chip oscillator
allowing it to perform an oscillator fail detect function.
s Programmable port output configuration options: quasi-bidirectional, open drain,
push-pull, input-only.
s Port ‘input pattern match’ detect. Port 0 may generate an interrupt when the value of
the pins match or do not match a programmable pattern.
s LED drive capability (20 mA) on all port pins. A maximum limit is specified for the
entire chip.
s Controlled slew rate port outputs to reduce EMI. Outputs have approximately 10 ns
minimum ramp times.
s Only power and ground connections are required to operate the P89LPC938 when
internal reset option is selected.
s Four interrupt priority levels.
s Eight keypad interrupt inputs, plus two additional external interrupt inputs.
s Schmitt trigger port inputs.
s Second data pointer.
s Emulation support.
9397 750 14051
Product data sheet
Rev. 01 — 25 February 2005
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
2 of 68


Part Number P89LPC938
Description 8-bit microcontroller
Maker NXP
Total Page 30 Pages
PDF Download

P89LPC938 Datasheet PDF

View PDF for Mobile








Similar Datasheet

1 P89LPC930 8-bit microcontrollers with two-clock 80C51 core 4 kB/8 kB 3 V Flash with 256-byte data RAM
NXP
2 P89LPC9301 8-bit Microcontroller
NXP
3 P89LPC9301A1 8-bit Microcontroller
NXP
4 P89LPC932 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB Flash with 512-byte data EEPROM and 768-byte RAM
NXP
5 P89LPC9321 8-bit microcontroller
NXP
6 P89LPC932A1 8-Bit Microcontroller
NXP Semiconductors
7 P89LPC933 (P89LPC933 - P89LPC936) 8-bit microcontroller
NXP
8 P89LPC9331 8-bit microcontroller
NXP Semiconductors
9 P89LPC934 (P89LPC933 - P89LPC936) 8-bit microcontroller
NXP





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy