900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




NXP Semiconductors Electronic Components Datasheet

PCA9539R Datasheet

16-bit I2C and SMBus low power I/O port

No Preview Available !

PCA9539; PCA9539R
16-bit I2C-bus and SMBus low power I/O port with interrupt
and reset
Rev. 9 — 8 November 2017
Product data sheet
1. General description
The PCA9539; PCA9539R is a 24-pin CMOS device that provides 16 bits of General
Purpose parallel Input/Output (GPIO) expansion with interrupt and reset for
I2C-bus/SMBus applications and was developed to enhance the NXP Semiconductors
family of I2C-bus I/O expanders. I/O expanders provide a simple solution when additional
I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.
The PCA9539; PCA9539R consists of two 8-bit configuration (input or output selection),
input, output and polarity inversion (active HIGH or active LOW operation) registers. The
system master can enable the I/Os as either inputs or outputs by writing to the I/O
configuration bits. The data for each input or output is kept in the corresponding Input or
Output register. The polarity of the read register can be inverted with the Polarity inversion
register. All registers can be read by the system master.
The PCA9539; PCA9539R is identical to the PCA9555 except for the removal of the
internal I/O pull-up resistor which greatly reduces power consumption when the I/Os are
held LOW, replacement of A2 with RESET and a different address range.
The PCA9539; PCA9539R open-drain interrupt output is activated when any input state
differs from its corresponding input port register state and is used to indicate to the system
master that an input state has changed.
The power-on reset sets the registers to their default values and initializes the device state
machine. In the PCA9539, the RESET pin causes the same reset/default I/O input
configuration to occur without de-powering the device, holding the registers and I2C-bus
state machine in their default state until the RESET input is once again HIGH. This input
requires a pull-up to VDD. In the PCA9539R however, only the device state machine is
initialized by the RESET pin and the internal general-purpose registers remain
unchanged. Using the PCA9539R RESET pin will only reset the I2C-bus interface should
it be stuck LOW to regain access to the I2C-bus. This allows the I/O pins to retain their last
configured state so that they can keep any lines in their previously defined state and not
cause system errors while the I2C-bus is being restored.
Two hardware pins (A0, A1) vary the fixed I2C-bus address and allow up to four devices to
share the same I2C-bus/SMBus.
2. Features and benefits
16-bit I2C-bus GPIO with interrupt and reset
Operating power supply voltage range of 2.3 V to 5.5 V (3.0 V to 5.5 V
for PCA9539PW/Q900 and PCA9539RPW/Q900)
5 V tolerant I/Os


NXP Semiconductors Electronic Components Datasheet

PCA9539R Datasheet

16-bit I2C and SMBus low power I/O port

No Preview Available !

NXP Semiconductors
PCA9539; PCA9539R
16-bit I2C-bus and SMBus low power I/O port with interrupt and reset
Polarity inversion register
Active LOW interrupt output
Active LOW reset input
Low standby current
Noise filter on SCL/SDA inputs
No glitch on power-up
Internal power-on reset
16 I/O pins which default to 16 inputs
0 Hz to 400 kHz clock frequency
ESD protection exceeds 2000 V HBM per JESD22-A114 and 1000 V CDM per
JESD22-C101
Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA
Offered in three different packages: SO24, TSSOP24, and HVQFN24
3. Ordering information
Table 1. Ordering information
Type number
Topside
marking
PCA9539BS
9539
Package
Name
HVQFN24
PCA9539RBS
539R
HVQFN24
PCA9539D
PCA9539D SO24
PCA9539PW
PCA9539PW TSSOP24
PCA9539PW/Q900[1] PCA9539PW TSSOP24
PCA9539RPW
PA9539RPW TSSOP24
PCA9539RPW/Q900[1] PA9539RPW TSSOP24
Description
plastic thermal enhanced very thin quad flat package;
no leads; 24 terminals; body 4 4 0.85 mm
plastic thermal enhanced very thin quad flat package;
no leads; 24 terminals; body 4 4 0.85 mm
plastic small outline package; 24 leads;
body width 7.5 mm
plastic thin shrink small outline package; 24 leads;
body width 4.4 mm
plastic thin shrink small outline package; 24 leads;
body width 4.4 mm
plastic thin shrink small outline package; 24 leads;
body width 4.4 mm
plastic thin shrink small outline package; 24 leads;
body width 4.4 mm
Version
SOT616-1
SOT616-1
SOT137-1
SOT355-1
SOT355-1
SOT355-1
SOT355-1
[1] PCA9539PW/Q900 and PCA9539RPW/Q900 are AEC-Q100 compliant. Contact I2C.support@nxp.com for PPAP.
3.1 Ordering options
Table 2. Ordering options
Type number
Orderable
part number
PCA9539BS
PCA9539BS,115
PCA9539BS,118
PCA9539BSHP
Package Packing method
HVQFN24 Reel 7” Q1/T1
*standard mark SMD[1]
HVQFN24 Reel 13” Q1/T1
*standard mark SMD[1]
HVQFN24 Reel 13” Q2/T3
*standard mark SMD[2]
Minimum Temperature
order
quantity
1500
Tamb = 40 C to +85 C
6000
Tamb = 40 C to +85 C
6000
Tamb = 40 C to +85 C
PCA9539_PCA9539R
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 9 — 8 November 2017
© NXP Semiconductors N.V. 2017. All rights reserved.
2 of 39


Part Number PCA9539R
Description 16-bit I2C and SMBus low power I/O port
Maker NXP
Total Page 3 Pages
PDF Download

PCA9539R Datasheet PDF

View PDF for Mobile








Similar Datasheet

1 PCA9539 16-bit I2C and SMBus low power I/O port
NXP
2 PCA9539 Remote 16-Bit I2C and SMBus Low-Power I/O Expander
etcTI
3 PCA9539R 16-bit I2C and SMBus low power I/O port
NXP





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy