datasheet4u.com

900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf





Nichicon
Nichicon

PCJ0G122MCL1GS Datasheet Preview

PCJ0G122MCL1GS Datasheet

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

No Preview Available !

PCJ0G122MCL1GS pdf
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CJ Chip Type, Low ESR,
Higher Capacitance
series
CK
Low ESR, Higher Capacitance, High ripple current.
Load life of 2000 hours at 105°C.
SMD type : Lead free reflow soldering condition at
260°C peak correspondence.
Compliant to the RoHS directive (2002/95/EC).
Low ESR
CJ
Specifications
Low ESR
Higher
Capacitance,
CF
Item
Performance Characteristics
Category Temperature Range 55 to +105°C
Rated Voltage Range
2.5 to 16V
Rated Capacitance Range 33 to 2700µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C
ESR ( 1)
Less than or equal to the specified value at 100kHz, 20°C
Leakage Current ( 2) Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C 1.25
Z55°C / Z+20°C 1.25
(100kHz)
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Resistance to
Soldering Heat
Marking
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed at
right, provided that it's temperature profile is measured at the
capacitor top and the terminal.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface shall
not exceed 60 seconds.
In the case of peak temp, less than 250°C, reflow soldering shall be
two times maximum.
In the case of peak temp, less than 260°C, reflow soldering shall be
once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Navy blue print on the case top
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Capacitance
Lot No.
Plastic platform
0.3 MAX.
C±0.2
Positive
Series
Voltage ( j:6.3v)
L
+0.1
- 0.4
Negative
H
Type numbering system (Example : 6.3V 220µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
PC J 0 J 2 2 1 MC L 1 GS
Taping code
Size code
Configuration
Capacitance toleranc (±20%)
Rated capacitance (220µF)
Rated voltage (6.3V)
Series name
Type
(mm)
Size φ5 × 6L φ6.3 × 6L φ6.3 × 8L φ8 × 7L φ8 × 8L φ8 × 10L φ8 × 12L φ10 × 8L φ10 × 10L φ10 × 12.7L
φD 5.0 6.3 6.3 8.0 8.0 8.0 8.0 10.0 10.0 10.0
L 5.9 5.9 7.9 6.9 7.9 9.9 11.9 7.9 9.9 12.6
A 6.0 7.3 7.3 9.0 9.0 9.0 9.0 11.0 11.0 11.0
B 5.3 6.6 6.6 8.3 8.3 8.3 8.3 10.3 10.3 10.3 Voltage
C 5.3 6.6 6.6 8.3 8.3 8.3 8.3 10.3 10.3 10.3
E 1.6 2.1 2.1 3.2 3.2 3.2 3.2 4.6 4.6 4.6
H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
V 2.5 4 6.3 10 16
Code e g j A C
Dimension table in next page.
CAT.8100Z



Nichicon
Nichicon

PCJ0G122MCL1GS Datasheet Preview

PCJ0G122MCL1GS Datasheet

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

No Preview Available !

PCJ0G122MCL1GS pdf
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CJ series
Standard Ratings
Rated Voltage
(V)(code)
2.5
(0E)
4
(0G)
6.3
(0J)
10
(1A)
16
(1C)
Surge Voltage
(V)
2.8
4.6
7.2
11.5
18.4
Rated Capacitance
(µF)
180
390
470
560
560
680
820
820
1000
1200
1500
1500
2200
2700
100
150
270
330
390
470
560
560
680
1000
1000
1200
1200
1500
1500
1800
1800
2200
100
120
220
270
330
330
390
470
820
820
820
1200
1500
1500
1800
47
56
68
120
150
220
270
330
390
470
680
33
39
68
82
100
100
120
150
180
220
220
270
330
Case Size
φD × L (mm)
5×6
6.3 × 6
6.3 × 8
6.3 × 8
8×7
8×7
8×8
8 × 12
8×8
10 × 8
8 × 10
8 × 12
10 × 10
10 × 12.7
5×6
5×6
6.3 × 6
6.3 × 6
6.3 × 8
8×7
8×7
8 × 12
8×8
8 × 10
10 × 8
8 × 12
10 × 10
8 × 12
10 × 10
10 × 10
10 × 12.7
10 × 12.7
5×6
5×6
6.3 × 6
6.3 × 8
6.3 × 8
8×7
8×7
8×8
8 × 10
8 × 12
10 × 8
10 × 10
10 × 10
10 × 12.7
10 × 12.7
5×6
5×6
5×6
6.3 × 6
6.3 × 8
8×7
8×7
8×8
8 × 10
10 × 8
10 × 10
5×6
5×6
6.3 × 6
6.3 × 8
6.3 × 8
8×7
8×7
8×8
8 × 10
8 × 10
10 × 8
8 × 12
10 × 10
tan δ
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please refer to page 3 for the minimum order quantity.
Leakage Current
(µA)
90
195
235
280
280
340
410
410
500
600
750
750
1100
1350
80
120
216
264
312
376
448
448
544
800
800
960
960
1200
1200
1440
1440
1760
126
151
277
340
416
416
491
592
1033
1033
1033
1512
1890
1890
2268
94
112
136
240
300
440
540
660
780
940
1360
105
125
217
262
320
320
384
480
576
704
704
864
1056
ESR (m)
Rated Ripple
(at 100kHz 20°C) (mArms)
Part Number
21
2670
PCJ0E181MCL1GS
15
3400
PCJ0E391MCL1GS
13
3600
PCJ0E471MCL1GS
13
3600
PCJ0E561MCL4GS
13
4100
PCJ0E561MCL1GS
13
4100
PCJ0E681MCL1GS
12
4260
PCJ0E821MCL6GS
9
5400
PCJ0E821MCL1GS
12
4260
PCJ0E102MCL1GS
13
4800
PCJ0E122MCL1GS
10
5220
PCJ0E152MCL6GS
9
5400
PCJ0E152MCL1GS
10
5500
PCJ0E222MCL1GS
9
5800
PCJ0E272MCL1GS
22
2610
PCJ0G101MCL1GS
22
2610
PCJ0G151MCL1GS
15
3200
PCJ0G271MCL1GS
15
3300
PCJ0G331MCL1GS
14
3470
PCJ0G391MCL1GS
14
3950
PCJ0G471MCL1GS
14
4000
PCJ0G561MCL1GS
9
5200
PCJ0G561MCL9GS
13
3950
PCJ0G681MCL1GS
10
5220
PCJ0G102MCL4GS
13
4300
PCJ0G102MCL1GS
9
5400
PCJ0G122MCL1GS
10
5500
PCJ0G122MCL6GS
9
5200
PCJ0G152MCL4GS
10
5500
PCJ0G152MCL1GS
10
5500
PCJ0G182MCL1GS
9
5600
PCJ0G182MCL9GS
9
5700
PCJ0G222MCL1GS
24
2500
PCJ0J101MCL1GS
24
2500
PCJ0J121MCL1GS
15
3200
PCJ0J221MCL1GS
14
3470
PCJ0J271MCL1GS
14
3470
PCJ0J331MCL4GS
14
3950
PCJ0J331MCL1GS
14
3950
PCJ0J391MCL1GS
13
3950
PCJ0J471MCL1GS
12
4770
PCJ0J821MCL6GS
10
5150
PCJ0J821MCL4GS
13
4500
PCJ0J821MCL1GS
12
5025
PCJ0J122MCL1GS
12
5025
PCJ0J152MCL1GS
10
5500
PCJ0J152MCL9GS
11
5200
PCJ0J182MCL1GS
28
2310
PCJ1A470MCL1GS
28
2310
PCJ1A560MCL1GS
28
2310
PCJ1A680MCL1GS
25
2530
PCJ1A121MCL1GS
21
2880
PCJ1A151MCL1GS
21
3220
PCJ1A221MCL1GS
21
3220
PCJ1A271MCL1GS
19
3390
PCJ1A331MCL1GS
17
4000
PCJ1A391MCL1GS
19
3800
PCJ1A471MCL1GS
13
4820
PCJ1A681MCL1GS
35
2070
PCJ1C330MCL1GS
35
2070
PCJ1C390MCL1GS
28
2390
PCJ1C680MCL1GS
24
2700
PCJ1C820MCL1GS
24
2700
PCJ1C101MCL4GS
24
3010
PCJ1C101MCL1GS
24
3010
PCJ1C121MCL1GS
22
3150
PCJ1C151MCL1GS
18
3890
PCJ1C181MCL1GS
18
3890
PCJ1C221MCL4GS
22
3450
PCJ1C221MCL1GS
16
4070
PCJ1C271MCL1GS
16
4350
PCJ1C331MCL1GS
Rated ripple current (mArms) at 105°C 100kHz
No marked, 1 will be put at 12th digit of type numbering system.
: In this case, 4 will be put at 12th digit of type numbering system.
: In this case, 6 will be put at 12th digit of type numbering system.
: In this case, 9 will be put at 12th digit of type numbering system.
CAT.8100Z


Part Number PCJ0G122MCL1GS
Description CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
Maker Nichicon
Total Page 2 Pages
PDF Download
PCJ0G122MCL1GS pdf
PCJ0G122MCL1GS Datasheet PDF
[partsNo] view html
View PDF for Mobile








Similar Datasheet

1 PCJ0G122MCL1GS CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS Nichicon
Nichicon
PCJ0G122MCL1GS pdf





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy