900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf






Nichicon

PCK0G561MCO1GS Datasheet Preview

PCK0G561MCO1GS Datasheet

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

No Preview Available !

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CK Chip Type, Ultra-low ESR
series
Ultra-low ESR, Higher Capacitance, High ripple current.
Load life of 2000 hours at 105°C.
SMD type : Lead free reflow soldering condition at 260°C peak
correspondence.
Compliant to the RoHS directive (2002/95/EC).
CJ
Low ESR
CK
Specifications
Item
Performance Characteristics
Category Temperature Range 55 to +105°C
Rated Voltage Range
2.5 to 6.3V
Rated Capacitance Range 220 to 2200µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C
ESR ( 1)
Less than or equal to the specified value at 100kHz, 20°C
Leakage Current ( 2) Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C 1.25
Z55°C / Z+20°C 1.25
(100kHz)
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Resistance to
Soldering Heat
Marking
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed at
right, provided that it's temperature profile is measured at the
capacitor top and the terminal.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface shall
not exceed 60 seconds.
In the case of peak temp, less than 250°C, reflow soldering shall be
two times maximum.
In the case of peak temp, less than 260°C, reflow soldering shall be
once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Navy blue print on the case top
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Capacitance
Lot No.
Plastic platform
0.3 MAX.
C±0.2
Positive
Type numbering system (Example : 6.3V 220µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
PCK 0 J 2 2 1 MCO 1 GS
Series
Voltage ( j:6.3v)
L
+0.1
- 0.4
Negative
H
(mm)
Size φ6.3 × 6L φ8 × 7L φ10 × 8L φ10 × 10L
φD 6.3
8.0 10.0 10.0
L 5.9 6.9 7.9 9.9
A 7.3
9.0 11.0 11.0
B 6.6
8.3 10.3 10.3 Voltage
C 6.6
8.3 10.3 10.3
E 2.1 3.2 4.6 4.6
H 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
V 2.5 4 6.3
Code e g
j
Taping code
Configuration
Capacitance toleranc (±20%)
Rated capacitance (220µF)
Rated voltage (6.3V)
Series name
Type
Dimension table in next page.
CAT.8100Z




Nichicon

PCK0G561MCO1GS Datasheet Preview

PCK0G561MCO1GS Datasheet

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

No Preview Available !

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CKseries
Standard Ratings
Rated Voltage Surge Voltage Rated Capacitance
(V)(code)
(V)
(µF)
390
2.5
(0E)
2.8
560
680
1200
2200
330
4
(0G)
4.6
470
560
1000
1800
220
6.3
(0J)
7.2
330
390
820
1500
Case Size
φD × L (mm)
6.3 × 6
8×7
8×7
10 × 8
10 × 10
6.3 × 6
8×7
8×7
10 × 8
10 × 10
6.3 × 6
8×7
8×7
10 × 8
10 × 10
tan δ
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
Leakage Current
ESR (m)
(µA) (at 100kHz 20°C)
293 10
420 9
510 9
900 9
1650
8
396 10
564 9
672 9
1200
9
2160
8
416 10
624 9
737 9
1550
9
2835
8
Rated Ripple
(mArms)
3900
4500
4500
5000
6000
3900
4500
4500
5000
6000
3900
4500
4500
5000
6000
Part Number
PCK0E391MCO1GS
PCK0E561MCO1GS
PCK0E681MCO1GS
PCK0E122MCO1GS
PCK0E222MCO1GS
PCK0G331MCO1GS
PCK0G471MCO1GS
PCK0G561MCO1GS
PCK0G102MCO1GS
PCK0G182MCO1GS
PCK0J221MCO1GS
PCK0J331MCO1GS
PCK0J391MCO1GS
PCK0J821MCO1GS
PCK0J152MCO1GS
Rated ripple current (mArms) at 105°C 100kHz
No marked, 1 will be put at 12th digit of type numbering system.
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please refer to page 3 for the minimum order quantity.
CAT.8100Z


Part Number PCK0G561MCO1GS
Description CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
Maker Nichicon
Total Page 2 Pages
PDF Download

PCK0G561MCO1GS Datasheet PDF

View PDF for Mobile








Similar Datasheet

1 PCK0G561MCO1GS CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
Nichicon





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy