900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf






Nichicon

UUD1V221MCL Datasheet Preview

UUD1V221MCL Datasheet

Aluminum Electrolytic Capacitors

No Preview Available !

ALUMINUM ELECTROLYTIC CAPACITORS
UD Chip Type, Low Impedance
series
Chip type, low impedance temperature range up to +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
UU Low Impedance
UD
Low Impedance WG
Specifications
Item
Performance Characteristics
Category Temperature Range – 55 ~ +105°C
Rated Voltage Range
6.3 ~ 50V
Rated Capacitance Range 1 ~ 1500µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA), whichever is greater.
tan δ
Measurement frequency : 120Hz, Temperature : 20°C
Rated voltage (V)
6.3
10
16
25
35
50
tan δ (MAX.) 0.26 (0.28) 0.20 (0.24) 0.16 (0.20) 0.14 (0.16) 0.12 (0.14) 0.12 (0.14)
( ) is φ8 over
Measurement frequency : 120Hz
Rated voltage (V)
6.3 10 16 25 35 50
Stability at Low Temperature Impedance ratio Z– 25°C / Z+20°C
3
2
2
2
2
2
ZT / Z20 (MAX.) Z– 55°C / Z+20°C
5
4
4
3
3
3
Endurance
Shelf Life
Resistance to soldering
heat
Marking
After 5000 hours' (2000 hours for φD 6.3)
application of rated voltage at 105°C , capacitors
meet the characteristic requirements listed at
right.
Capacitance change
tan δ
Leakage current
Within ±30% of initial value
200% or less of initial specified value
Initial specified value or less
After leaving capacitors under no load at 105°C for 1000 hours,
they meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristic requirements
listed at right.
Capacitance change
tan δ
Leakage current
Black print on the case top.
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Chip Type
(φ4 ~ 6.3)
Voltage (C:16V)
Series
Plastic platform
0.3 MAX.
C±0.2
Positive
Lot No.
Capacitance
(φ8, φ10×10L)
Voltage (V:35V)
Series
Trade mark
L±0.3
H
Plastic platform
0.3 MAX.
C±0.2
Negative
Positive
Lot No.
Capacitance
L±0.5
Pressure relief vent
Voltage
V 6.3 10 16 25 35 50
Code j A C E V H
Dimension table in next page.
www.DataSheet.in
Negative
H
Type numbering system (Example : 16V 22µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UUD 1C 2 2 0 M CR 1GS
Package code
Configuration
Capacitance tolerance (±20%)
Rated Capacitance (22µF)
Rated voltage (16V)
φD×L
4 ~ 6.3
8 10
Code
CR
NR
Series name
Type
The lead-free product is also available upon request.
In this case, L will be put at 11th digit of type numbering system.
(mm)
φ D × L 4 × 5.8 5 × 5.8 6.3 × 5.8 6.3 × 7.7 8 × 10 10 × 10
A 1.8 2.1 2.4 2.4 2.9 3.2
B 4.3 5.3 6.6 6.6 8.3 10.3
C 4.3 5.3 6.6 6.6 8.3 10.3
E 1.0 1.3 2.2 2.2 3.1 4.5
L 5.8 5.8 5.8 7.7 10 10
H 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.8 ~ 1.1 0.8 ~ 1.1
CAT.8100T




Nichicon

UUD1V221MCL Datasheet Preview

UUD1V221MCL Datasheet

Aluminum Electrolytic Capacitors

No Preview Available !

ALUMINUM ELECTROLYTIC CAPACITORS
UD series
Dimensions
φ D × L (mm)
V 6.3 10 16 25 35 50
Cap.
(µF) Code
0J
1A
1C
1E
1V
1H
1 010
4 × 5.8 5.00 30
2.2 2R2
4 × 5.8 5.00 30
3.3 3R3
4 × 5.8 5.00 30
4.7 4R7
4 × 5.8 1.80 80 5 × 5.8 1.52 85
10 100
4 × 5.8 1.80 80 5 × 5.8 0.76 150 6.3 × 5.8 0.88 165
15 150
4 × 5.8 1.80 80 5 × 5.8 0.76 150 5 × 5.8 0.76 150 6.3 × 5.8 0.88 165
22 220
4 × 5.8 1.80 80 5 × 5.8 0.76 150 5 × 5.8 0.76 150 5 × 5.8 0.76 150 6.3 × 5.8 0.88 165
27 270 4 × 5.8 1.80 80 5 × 5.8 0.76 150 5 × 5.8 0.76 150 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.68 185
33 330 5 × 5.8 0.76 150 5 × 5.8 0.76 150 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.68 185
47 470 5 × 5.8 0.76 150 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.68 185
56 560 5 × 5.8 0.76 150 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.34 280 8 × 10 0.34 300
68 680 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.34 280 8 × 10 0.34 300
100 101 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.34 280 8 × 10 0.17 450 8 × 10 0.34 300
150 151 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.34 280 8 × 10 0.17 450 8 × 10 0.17 450 10 × 10 0.18 670
220 221 6.3 × 5.8 0.44 230 6.3 × 7.7 0.34 280 6.3 × 7.7 0.34 280 8 × 10 0.17 450 8 × 10 0.17 450 10 × 10 0.18 670
330 331 6.3 × 7.7 0.34 280 8 × 10 0.17 450 8 × 10 0.17 450 8 × 10 0.17 450 10 × 10 0.09 670
470 471 8 × 10 0.17 450 8 × 10 0.17 450 8 × 10 0.17 450 10 × 10 0.09 670
680 681 8 × 10 0.17 450 10 × 10 0.09 670 10 × 10 0.09 670
1000
1500
102 8 × 10 0.17 450 10 × 10 0.09 670
152 10 × 10 0.09 670
Rated
Case size Impedance
ripple
Max. impedance () at 20°C 100kHz, Rated Ripple (mA rms) at 105°C 100kHz
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz
Coefficient
0.35 0.50 0.64 0.83
10 kHz~
1.00
Taping specifications are given in page 22.
Recommended land size are given in page 23
Please refer to page 3 for the minimum order quantity.
www.DataSheet.in
CAT.8100T


Part Number UUD1V221MCL
Description Aluminum Electrolytic Capacitors
Maker Nichicon
Total Page 2 Pages
PDF Download

UUD1V221MCL Datasheet PDF

View PDF for Mobile








Similar Datasheet

1 UUD1V221MCL ALUMINUM ELECTROLYTIC CAPACITORS
Nichicon corporation
2 UUD1V221MCL Aluminum Electrolytic Capacitors
Nichicon





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy