900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Renesas Electronics Components Datasheet

HIP1020 Datasheet

Hot Plug Controller

No Preview Available !

HIP1020
Single, Double or Triple-Output Hot Plug Controller
The HIP1020 applies a linear voltage ramp to the gates of
any combination of 3.3V, 5V, and 12V MOSFETs. The
internal charge pump doubles a 12V bias or triples a 5V bias
to deliver the high-side drive capability required when using
more cost-effective N-Channel MOSFETs. The 5V/ms ramp
rate is controlled internally and is the proper value to turn on
most devices within the Device-Bay-specified di/dt limit. If a
slower rate is required, the internally-determined ramp rate
can be over ridden using an optional external capacitor.
When VCC = 12V, the charge pump ramps the voltage on
HGATE from zero to 22V in about 4ms. This allows either a
standard or a logic-level MOSFET to become fully enhanced
when used as a high-side switch for 12V power control. The
voltage on LGATE ramps from zero to 16V allowing the
simultaneous control of 3.3V and/or 5V MOSFETs.
When VCC = 5V, the charge pump enters voltage-tripler
mode. The voltage on HGATE ramps from zero to 12.5V in
about 3ms while LGATE ramps to 12.0V. This mode is ideal
for control of high-side MOSFET switches used in 3.3V and
5V power switching when 12V bias is not available.
Ordering Information
PART
NUMBER
TEMP.
RANGE (oC)
PACKAGE
PKG.
DWG. #
HIP1020CK-T
0 to 70 5 Ld SOT23 T + R P5.064
HIP1020CKZ-T
(See Note)
0 to 70
5 Ld SOT23 T + R P5.064
(Pb-free)
NOTE: Intersil Pb-free products employ special Pb-free material sets; molding
compounds/die attach materials and 100% matte tin plate termination finish,
which is compatible with both SnPb and Pb-free soldering operations. Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that
meet or exceed the Pb-free requirements of IPC/JEDEC J Std-020B.
DATASHEET
FN4601
Rev 2.00
July 2004
Features
• Rise Time Controlled to Device-Bay Specifications
• No Additional Components Required
• Internal Charge Pump Drives N-Channel MOSFETs
• Drives any Combination of One, Two or Three Outputs
• Internally-Controlled Turn-On Ramp
- Optional Capacitor Selects Slower Rates
• Prevents False Turn on During Hot Insertion
• Operates using 12V or 5V Bias
• Improves Device Bay Peripheral Size Cost and Complex-
ity
- Minimal Component Count
- Tiny 5-Pin SOT23 Package
• Controls Standard and Logic-Level MOSFETs
• Compatible with TTL and 3.3V Logic Devices
• Shutdown Current . . . . . . . . . . . . . . . . . . . . . . . . . . < 1A
• Operating Current . . . . . . . . . . . . . . . . . . . . . . . . . .< 3mA
Applications
• Device Bay Peripherals
• Hot Plug Control
• Power Distribution Control
Pinout
HIP1020 (SOT23)
TOP VIEW
VCC 1
GND 2
LGATE 3
5 EN
4 HGATE
FN4601 Rev 2.00
July 2004
Page 1 of 6


Renesas Electronics Components Datasheet

HIP1020 Datasheet

Hot Plug Controller

No Preview Available !

HIP1020
Typical Applications
HIP1020
1 CHARGE
PUMP
2
ENABLE
5 OPTIONAL
C1
34
V12 V12,OUT
V5 V5,OUT
V33 V33,OUT
FIGURE 1A. DEVICE-BAY HOT PLUG CONTROLLER WITH
VCC = 12V
HIP1020
1 CHARGE
PUMP
2
ENABLE
5 OPTIONAL
C1
34
V5 V5,OUT
V33 V33,OUT
FIGURE 1B. DEVICE-BAY HOT PLUG CONTROLLER WITH
VCC = 5V
Pin Descriptions
PIN SYMBOL
FUNCTION
DESCRIPTION
1
VCC
Bias Supply
Connect this pin to either a 12V or a 5V source. The HIP1020 detects the bias-voltage level at
pin 1 and decides whether to operate as a voltage-doubler or a voltage-tripler. Consequently,
it is not recommended to operate with bias voltages between 5V (10%) and 12V (10%). In
the absence of an enable signal at pin 5, the current into pin 1 is less than 1A. It is necessary
for voltage to be present at pin 1 prior to applying an enable signal at pin 5.
2
GND
Ground
Connect to the negative rail of the supply that is connected to pin 1.
3
LGATE
Gate Driver for the 5V When VCC = 12V, connect this pin to the gate(s) of the 5V and/or 3.3V MOSFETs. When VCC
and/or 3.3V
= 5V, connect this pin to the gate of a 3.3V MOSFET. Upon a rising edge on EN (pin 5), the
MOSFET(s)
voltage on this pin will ramp linearly to ~16V when VCC = 12V and ~12V when VCC = 5V. An
internal dv/dt activated clamp shunts coupled noise to ground preventing unintended turn on at
either output. The internal dv/dt-activated clamp also protects pin 5.
4 HGATE 12V or 5V MOSFET When VCC = 12V, connect this pin to the gate of the 12V MOSFET. When VCC = 5V, connect
Gate Driver
this pin to the gate of the 5V MOSFET. Upon a rising edge on EN (pin 5), the voltage on this
pin will ramp linearly to ~22V when VCC = 12V and ~13V when VCC = 5V.
5 EN Enable
Connect a TTL or 3.3V logic signal to this pin to control the outputs at pins 3 and 4. A rising
edge on pin 5 initiates the linear voltage ramps at pins 3 and 4. Be sure that the device driving
EN does not enter a high-impedance state when enabling is not desired and that it’s maximum
rise time does not exceed 100s.
FN4601 Rev 2.00
July 2004
Page 2 of 6


Part Number HIP1020
Description Hot Plug Controller
Maker Renesas
PDF Download

HIP1020 Datasheet PDF






Similar Datasheet

1 HIP1020 Hot Plug Controller
Renesas





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z



Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy