datasheet4u.com

900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




STMicroelectronics Electronic Components Datasheet

M93S66 Datasheet

4Kbit / 2Kbit and 1Kbit 16-bit wide MICROWIRE Serial Access EEPROM with Block Protection

No Preview Available !

M93S66 pdf
M93S66, M93S56
M93S46
4Kbit, 2Kbit and 1Kbit (16-bit wide)
MICROWIRE Serial Access EEPROM with Block Protection
FEATURES SUMMARY
s Industry Standard MICROWIRE Bus
s Single Supply Voltage:
– 4.5V to 5.5V for M93Sx6
– 2.5V to 5.5V for M93Sx6-W
– 1.8V to 5.5V for M93Sx6-R
s Single Organization: by Word (x16)
s Programming Instructions that work on: Word or
Entire Memory
s Self-timed Programming Cycle with Auto-Erase
s User Defined Write Protected Area
s Page Write Mode (4 words)
s Ready/Busy Signal During Programming
s Speed:
– 1MHz Clock Rate, 10ms Write Time (Current
product, identified by process identification
letter F or M)
– 2MHz Clock Rate, 5ms Write Time (New
Product, identified by process identification
letter W)
s Sequential Read Operation
s Enhanced ESD/Latch-Up Behavior
s More than 1 Million Erase/Write Cycles
s More than 40 Year Data Retention
Figure 1. Packages
8
1
PDIP8 (BN)
8
1
SO8 (MN)
150 mil width
TSSOP8 (DS)
3x3mm body size
TSSOP8 (DW)
169 mil width
May 2003
1/32


STMicroelectronics Electronic Components Datasheet

M93S66 Datasheet

4Kbit / 2Kbit and 1Kbit 16-bit wide MICROWIRE Serial Access EEPROM with Block Protection

No Preview Available !

M93S66 pdf
M93S66, M93S56, M93S46
SUMMARY DESCRIPTION
This specification covers a range of 4K, 2K, 1K bit
serial Electrically Erasable Programmable Memo-
ry (EEPROM) products (respectively for M93S66,
M93S56, M93S46). In this text, these products are
collectively referred to as M93Sx6.
Figure 2. Logic Diagram
D
C
S
PRE
W
VCC
M93Sx6
VSS
Q
AI02020
Table 1. Signal Names
S Chip Select Input
D Serial Data Input
Q Serial Data Output
C Serial Clock
PRE
Protection Register Enable
W Write Enable
VCC Supply Voltage
VSS Ground
The M93Sx6 is accessed through a serial input (D)
and output (Q) using the MICROWIRE bus proto-
col. The memory is divided into 256, 128, 64 x16
bit words (respectively for M93S66, M93S56,
M93S46).
The M93Sx6 is accessed by a set of instructions
which includes Read, Write, Page Write, Write All
and instructions used to set the memory protec-
tion. These are summarized in Table 2 and 3).
A Read Data from Memory (READ) instruction
loads the address of the first word to be read into
an internal address pointer. The data contained at
this address is then clocked out serially. The ad-
dress pointer is automatically incremented after
the data is output and, if the Chip Select Input (S)
is held High, the M93Sx6 can output a sequential
stream of data words. In this way, the memory can
be read as a data stream from 16 to 4096 bits (for
the M93S66), or continuously as the address
counter automatically rolls over to 00h when the
highest address is reached.
Within the time required by a programming cycle
(tW), up to 4 words may be written with help of the
Page Write instruction. the whole memory may
also be erased, or set to a predetermined pattern,
by using the Write All instruction.
Within the memory, a user defined area may be
protected against further Write instructions. The
size of this area is defined by the content of a Pro-
tection Register, located outside of the memory
array. As a final protection step, data may be per-
manently protected by programming a One Time
Programming bit (OTP bit) which locks the Protec-
tion Register content.
Programming is internally self-timed (the external
clock signal on Serial Clock (C) may be stopped or
left running after the start of a Write cycle) and
does not require an erase cycle prior to the Write
instruction. The Write instruction writes 16 bits at a
time into one of the word locations of the M93Sx6,
the Page Write instruction writes up to 4 words of
16 bits to sequential locations, assuming in both
cases that all addresses are outside the Write Pro-
tected area. After the start of the programming cy-
cle, a Busy/Ready signal is available on Serial
Data Output (Q) when Chip Select Input (S) is
driven High.
Figure 3. DIP, SO and TSSOP Connections
M93Sx6
S1
C2
D3
Q4
8 VCC
7 PRE
6W
5 VSS
AI02021
Note: 1. See page 26 (onwards) for package dimensions, and how
to identify pin-1.
2/32


Part Number M93S66
Description 4Kbit / 2Kbit and 1Kbit 16-bit wide MICROWIRE Serial Access EEPROM with Block Protection
Maker ST Microelectronics
Total Page 30 Pages
PDF Download
M93S66 pdf
M93S66 Datasheet PDF
[partsNo] view html
View PDF for Mobile








Similar Datasheet

1 M93S66 4Kbit / 2Kbit and 1Kbit 16-bit wide MICROWIRE Serial Access EEPROM with Block Protection ST Microelectronics
ST Microelectronics
M93S66 pdf
2 M93S66-125 MICROWIRE serial EEPROM STMicroelectronics
STMicroelectronics
M93S66-125 pdf
3 M93S66-W MICROWIRE bus EEPROM STMicroelectronics
STMicroelectronics
M93S66-W pdf





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy