900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Sharp Electronic Components Datasheet

PC901V Datasheet

Digital Output Type OPIC Photocoupler

No Preview Available !

PC901V
PC901V
Digital Output Type OPIC
Photocoupler
s Features
1. Normal-ON operation, open collector out-
put
2. Operating supply voltage ( VCC : 3 to 15V )
3. TTL and LSTTL compatible output
4. High isolation voltage between input and
output ( Viso : 5 000V rms )
5. High sensitivity ( IFLH : MAX. 2.0mA at
Ta = 25˚C )
6. Recognized by UL, file No. 64380
s Applications
1. Isolation between logic circuits
2. Logic level shifters
3. Line receivers
4. Replacements for relays and pulse trans-
formers
5. Noise reduction
s Outline Dimensions
Anode
mark
654
PC901V
123
0.9 ± 0.2
1.2 ± 0.3
7.12 ± 0.5
( Unit : mm)
Internal connection
diagram
Voltage regulator
654
Amp
123
7.62 ± 0.3
0.5 ± 0.1
2.54 ± 0.25
1 Anode
2 Cathode
3 NC
θ = 0 to 13 ˚
0.26 ± 0.1
θ
4 VO
5 GND
6 VCC
θ
s Absolute Maximum Ratings
Input
Output
Parameter
Forward current
*1Peak forward current
Reverse voltage
Power dissipation
Supply voltage
High level output voltage
Low level output current
Power dissipation
Total power dissipation
*2Isolation voltage
Operating temperature
Storage temperature
*3Soldering temperature
*1 Pulse width <= 100µs, Duty ratio : 0.001
*2 40 to 60% RH, AC for 1 minute
*3 For 10 seconds
* “ OPIC ” ( Optical IC ) is a trademark of the SHARP Corporation.
An OPIC consists of a light-detecting element and signal-
processing circuit integrated onto a single chip.
( Ta = 25˚C)
Symbol
IF
I FM
VR
P
V CC
V OH
I OL
PO
P tot
V iso
T opr
T stg
T sol
Rating
50
1
6
70
16
16
50
150
170
5 000
- 25 to + 85
- 40 to + 125
260
Unit
mA
A
V
mW
V
V
mA
mW
mW
V rms
˚C
˚C
˚C
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs,
data books, etc. Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device.


Sharp Electronic Components Datasheet

PC901V Datasheet

Digital Output Type OPIC Photocoupler

No Preview Available !

PC901V
s Electro-optical Characteristics
( Ta = 0 to + 70˚C unless otherwise specified )
Parameter
Symbol
Conditions
MIN.
Input
Forward voltage
Reverse current
IF = 4mA
VF
IF = 0.3mA
IR Ta = 25˚C, V R = 4V
-
0.7
-
Terminal capacitance
Ct Ta = 25˚C, V = 0, f = 1kHz
-
Operating supply voltage
V CC
3
Low level output voltage
V OL IOL = 16mA, V CC = 5V, I F = 4mA
-
Output
High level output current
I OH V O = V CC = 15V, I F = 0
-
Low level supply current
ICCL V CC = 5V, I F = 0
-
High level supply current
I CCH V CC = 5V, I F = 4mA
-
*4 “ LH ” threshold input
current
*5 “ HL ” threshold input
current
*6 Hysteresis
I FLH
I FHL
I FHL /I FLH
Ta = 25˚C, V CC = 5V, R L = 280
VCC = 5V, R L = 280
Ta = 25˚C, V CC = 5V, R L = 280
VCC = 5V, R L = 280
VCC = 5V, R L = 280
-
-
0.4
0.3
0.5
Transfer
charac-
teristics
Isolation resistance
“ LH ” propagation delay time
“ HL ” propagation delay time
Rise time
Fall time
*8Instantaneous common mode rejec-
tion voltage ( High level output )
*8Instantaneous common mode rejec-
tion voltage ( Low level output)
R ISO
t PLH
t PHL
tr
tf
CM H
CML
Ta = 25˚C, DC500V, 40 to 60% RH
5 x 1010
Ta = 25˚C
VCC = 5V, I F = 4mA
RL = 280
VCM = 600V (peak ), VO(MIN. ) = 2V
IF = 4mA, R L = 280 , Ta = 25˚C
VCM = 600V (peak ), VO(MAX.) = 0.8V
IF = 0, R L = 280 , Ta = 25˚C
-
-
-
-
-
-
*4 I FLH represents forward current when output goes from low to high.
*5 I FHL represents forward current when output goes from high to low.
*6 Hysterisis stands for I FHL /I FLH
*7 Test circuit for response time is shown below.
*8 Test circuit for CMH,CML shown below.
TYP.
1.1
1.0
-
30
-
0.2
-
2.5
2.7
1.1
-
0.8
-
0.7
1011
1
2
0.1
0.05
- 2000
2000
MAX.
1.4
-
10
250
15
0.4
100
5.0
5.5
2.0
4.0
-
-
0.9
-
3
6
0.5
0.5
-
-
Unit
V
µA
pF
V
V
µA
mA
mA
mA
mA
-
µs
V/ µ s
V/ µ s
Test Circuit for Response Time
tr = tf = 0.01µ s
ZO = 50
Voltage regulator
VIN
47
Amp.
Test Circuit for CM H, CM L
Switch for
Infrared LED
B
IF
A
Voltage regulator
Amp.
+-
VCM
5V
280
VO
0.1µF
VIN
VO
tPLH
1.5V
tr
50 %
tPHL
tf
90 % VOH
10 %
VOL
5V
280
VO
0.1µ F
VCM
Switch for Infrared LED at A (IF = 0)
VO(MAX.) = 0.8V
Switch for Infrared LED at B (IF= 4mA)
VO(MIN.) = 2.0V
600V
VOL
GND
GND


Part Number PC901V
Description Digital Output Type OPIC Photocoupler
Maker Sharp Electrionic Components
Total Page 5 Pages
PDF Download

PC901V Datasheet PDF

View PDF for Mobile








Similar Datasheet

1 PC901V Digital Output Type OPIC Photocoupler
Sharp Electrionic Components





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy