900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Vishay Intertechnology Electronic Components Datasheet

TSOP18640 Datasheet

IR Receiver

No Preview Available !

www.vishay.com
TSOP182.., TSOP184.., TSOP186..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
1
2
3
ADDITIONAL RESOURCES
3D 3D
3D Models
FEATURES
• Improved dark sensitivity
• Improved immunity against optical noise
• Improved immunity against Wi-Fi noise
• Low supply current
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Supply voltage: 2.5 V to 5.5 V
• Insensitive to supply voltage ripple and noise
19026
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
MECHANICAL DATA
Pinning for TSOP18...:
1 = OUT, 2 = GND, 3 = VS
DESCRIPTION
The TSOP18... series devices are the latest generation miniaturized IR receiver modules for infrared remote control systems.
This series provides improvements in sensitivity to remote control signals in dark ambient as well as in sensitivity in the presence
of optical disturbances e.g. from CFLs. The robustness against spurious pulses originating from Wi-Fi signals has been
enhanced.
The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. The
demodulated output signal can be directly connected to a microprocessor for decoding.
The TSOP182.., TSOP184.., and TSOP186.. series devices are designed to receive long burst codes (10 or more carrier cycles
per burst). The third digit designates the AGC level (AGC2, AGC4, or AGC6) and the last two digits designate the band-pass
frequency (see table below). The higher the AGC, the better noise is suppressed, but the lower the code compatibility. AGC2
provides basic noise suppression, AGC4 provides enhanced noise suppression and AGC6 provides maximized noise
suppression. Generally, we advise to select the highest AGC that satisfactorily receives the desired remote code.
These components have not been qualified to automotive specifications.
PARTS TABLE
AGC
30 kHz
33 kHz
Carrier
36 kHz
frequency 38 kHz
40 kHz
56 kHz
Package
Pinning
Dimensions (mm)
Mounting
Application
Best choice for
BASIC NOISE SUPPRESSION ENHANCED NOISE SUPPRESSION MAXIMIZED NOISE SUPPRESSION
(AGC2)
(AGC4)
(AGC6)
TSOP18230
TSOP18430
TSOP18630
TSOP18233
TSOP18433
TSOP18633
TSOP18236
TSOP18436 (2)(5)(7)
TSOP18636 (6)
TSOP18238
TSOP18438 (3)(4)(10)(11)
TSOP18638
TSOP18240 (12)
TSOP18440
TSOP18640
TSOP18256 (1)
TSOP18456 (9)
TSOP18656 (8)
Minicast
1 = OUT, 2 = GND, 3 = VS
5.0 W x 6.95 H x 4.8 D
Leaded
Remote control
(1) Cisco (2) MCIR (3) Mitsubishi (4) NEC (5) Panasonic (6) RC-5 (7) RC-6
(8) RCA (9) r-step (10) Sejin 4PPM (11) Sharp (12) Sony
Note
• 30 kHz and 33 kHz only available on written request
Rev. 1.6, 16-Dec-2019
1 Document Number: 82739
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000


Vishay Intertechnology Electronic Components Datasheet

TSOP18640 Datasheet

IR Receiver

No Preview Available !

www.vishay.com
BLOCK DIAGRAM
16833-13
30 kΩ
Input
AGC
Band
pass
Demo-
dulator
PIN Control circuit
TSOP182.., TSOP184.., TSOP186..
Vishay Semiconductors
APPLICATION CIRCUIT
17170-11
3
R1
Transmitter IR receiver
with
TSALxxxx
1
VS
C1
+ VS
OUT
μC
GND
VO GND
2
R1 and C1 recommended to reduce supply ripple for VS < 2.8 V
ABSOLUTE MAXIMUM RATINGS
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
Supply voltage
Supply current
VS -0.3 to +6
V
IS 3 mA
Output voltage
VO -0.3 to (VS + 0.3)
V
Output current
Junction temperature
IO 5 mA
Tj 100 °C
Storage temperature range
Tstg -25 to +85
°C
Operating temperature range
Power consumption
Soldering temperature
Tamb 85 °C
t 10 s, 1 mm from case
Tamb
Ptot
Tsd
-25 to +85
10
260
°C
mW
°C
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL MIN.
TYP.
MAX.
Supply current
Ev = 0, VS = 3.3 V
Ev = 40 klx, sunlight
ISD 0.55 0.70 0.90
ISH - 0.80 -
Supply voltage
Transmission distance
Output voltage low
Minimum irradiance
Maximum irradiance
Directivity
Ev = 0, test signal see Fig. 1,
IR diode TSAL6200, IF = 50 mA
IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1
Pulse width tolerance:
tpi - 3.5/f0 < tpo < tpi + 3.5/f0, test signal see Fig. 1
tpi - 3.5/f0 < tpo < tpi + 3.5/f0, test signal see Fig. 1
Angle of half transmission distance
VS
d
VOSL
Ee min.
Ee max.
ϕ1/2
2.5
-
-
-
30
-
-
24
-
0.12
-
± 45
5.5
-
100
0.25
-
-
UNIT
mA
mA
V
m
mV
mW/m2
W/m2
°
Rev. 1.6, 16-Dec-2019
2 Document Number: 82739
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000


Part Number TSOP18640
Description IR Receiver
Maker Vishay
PDF Download

TSOP18640 Datasheet PDF






Similar Datasheet

1 TSOP18640 IR Receiver
Vishay





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z



Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy