Recommended Operating Conditions
140
120
100
Absolute Maximum Ratings, TA=25°C
Stresses in excess of the Absolute Maximum Ratings can cause permanent
damage to the device. These are absolute stress ratings only. Functional opera-
tion of the device is not implied at these or any other conditions in excess of
those given in the operational sections of the data sheet. Exposure to maximum
rating conditions for extended periods can adversely affect device reliability.
80
IFon=3.0 mA
60 IFon=5.0 mA
IFon=7.0 mA
40 IFon=8.0 to 20 mA
Ambient Temperature Range (TA) .................................... –40 to +85°C
Storage Temperature Range (Tstg) ................................. –40 to +150°C
Pin Soldering Temperature (t=10 s max) (TS) ............................. 260°C
Input/Output Isolation Voltage (VISO) .................................. 5300 VRMS
Pole-to-Pole Isolation Voltage (S1 to S2)...................................... 500 V
20 LED Continuous Forward Current (IF) .........................................50 mA
0
–40 –20 0 20 40 60
Ambient Temperature (°C)
80
LED Reverse Voltage (IR≤10 µA) (VR)........................................... 8.0 V
DC or Peak AC Load Voltage (IL≤50 µA) (VL) .............................. 200 V
Continuous DC Load Current (IL)
One Pole Operating.................................................................200 mA
www.DataSheet4U.com
Two Poles Operating ...............................................................140 mA
Peak Load Current (t=100 ms) (single shot) (IP) ................................ †
Output Power Dissipation (continuous) (PDISS)........................ 600 mW
† Refer to Current Limit Performance Application Note for a discussion on
relay operation during transient currents.
Electrical Characteristics, TA=25°C
Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of
engineering evaluations. Typical values are for information only and are not part of the testing requirements.
Parameter
Input
LED Forward Current, Switch Turn-on
LED Forward Current, Switch Turn-off
LED Forward Voltage
Output
ON-resistance
Sym. Min.
Typ.
Max.
Units Test Conditions
IFon
IFoff
VF
RON
—
0.2
1.15
6.0
2.0
0.8
1.26
10
3.0
—
1.45
15
mA
mA
V
Ω
IL=100 mA, t=10 ms
VL±150 V
IF=10 mA
IF=5.0 mA, IL=50 mA
Pole-to-Pole ON-resistance Matching (S1 to S2)
—
—
0.1 1.0 ∆Ω IF=5.0 mA, IL=50 mA
OFF-resistance
ROFF
0.5
5000
—
GΩ IF=0 mA, VL=±100 V
Current Limit
ILMT
300
360
460
mA
IF=5.0 mA, t=5.0 ms
VL±5.0 V
Off-state Leakage Current
—
—
0.02
200
nA
IF=0 mA, VL=±100 V
— — 1.0 µA IF=0 mA, VL=±200 V
Output Capacitance
— — 60 — pF IF=0 mA, VL=1.0 V
— 15 —
IF=0 mA, VL=50 V
Pole-to-Pole Capacitance (S1 to S2)
— — 3.0 — pF IF=0 mA
— 4.0 —
IF=5.0 mA
Switch Offset
—
—
0.15
—
V
IF=5.0 mA
Transfer
Input/Output Capacitance
Turn-on Time
Turn-off Time
CISO
ton
toff
—
—
—
1.1 — pF VISO=1.0 V
1.6 2.5 ms IF=10.0 mA, IL=50 mA
0.65
2.5
ms
IF=10.0 mA, IL=50 mA
Document Number: 83813
Revision 17-August-01
www.vishay.com
3–68
