900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf






WICI

MM4001 Datasheet Preview

MM4001 Datasheet

RTD INPUT TRANSMITTERS

No Preview Available !

MM4001 &
MM4001ISO
RTD INPUT
TRANSMITTERS
DESCRIPTION
OPTIONS
The MM4001 modules are used to provide The following options are available on the
an output voltage or current proportional MM4001 & MM4001ISO:
to an RTD input signal. It is useful in
measuring temperatures with a variety
of RTD materials.
U All circuit boards conformal coated for
protection against moisture.
DC Power
The module utilizes a single constant-
Inverter-isolated 12 V or 24 V DC
current source to excite the RTD and
power.
also has an accurate and stable leadwire CONTROLS
compensation circuit for compensating Two controls, ZERO and SPAN, are
3-wire RTDs against leadwire effects. accessible from the top of the module.
The MM4001ISO utilizes pulse width
modulation to develop a pulse train with
a duty cycle proportional to input signal
amplitude. This pulse train is coupled
through a pulse transformer where the
duty cycle data is converted to a
proportional DC level in the output circuit.
CALIBRATION
The MM4001 modules are shipped
precalibrated, if there is a need to
recalibrate, proceed as follows:
Refer to the instrument's label to determine
your instrument's supply voltage and input
and output ranges. Refer to the "Block
Diagram and Pin Connections" for pin
connections.
Connect a precision decade resistance,
potentiometer or RTD simulator to the
input. To avoid errors due to the
resistances of the connection wires,
use a three-wire connection as shown
in the “Block Diagram and Pin
Connections”. Connect a precision DC
voltage or current meter to the output.
Set the input resistance to the low end of
the input range and adjust the ZERO
control for the low-end output voltage or
current. Increase the input resistance to
full scale and adjust the SPAN control for
the full-scale output. Repeat until both
readings are correct.
MOUNTING
The module is designed to plug into a
standard 8 pin relay socket. (MP008) is a
molded plastic socket that can be mounted
on a flat surface or snapped into 2¾ inch
wide PVC track (TRK 48).
A spring hold-down clip (CLP1) is avail-
able for installations where vibration may
be a problem.
A DIN-rail mounted socket (DMP008) is
available for 35mm symmetrical rail.
A Killark HK Series explosion-proof hous-
ing with dome and 8-pin socket is
available(HKB-HK2D-8).
WARRANTY
The Mighty Module Series of products
carry a limited warranty of 10 + 5 years.
In the event of a failure due to defective
material or workmanship, during the 10
year period, the unit will be repaired or
replaced at no charge. For a period of 5
years after the initial 10 year warranty,
the unit will be repaired, if possible, for a
cost of 10 % of the original purchase
price.
CASE DIMENSIONS INCHES [mm]
1
http://www.Datasheet4U.com
2




WICI

MM4001 Datasheet Preview

MM4001 Datasheet

RTD INPUT TRANSMITTERS

No Preview Available !

SPECIFICATIONS
RTD Input
3-wire or 2-wire, 10 ohms to 2000
ohms
Input Range
select any range within RTD limit
[min span 25°F/14°C (100°F/55°C with
10 ohms RTD)]
Excitation Current
10 ohms 10 mA
100 ohms 5 mA
1000 ohms 0.5 mA
2000 ohms 0.2 mA
Output Range
Voltage
select any range from -10 V to +15 V,
10 mA max load (min span 0.2 V)
Current
select any range from 0 to 50 mA
max,
>24 V compliance (1200 ohms max at
20 mA)
18 V compliance for ISO option if
fullscale output >20 mA
Open Sensor Output
full scale
Accuracy
±0.1% of span
Linearity (Pt RTD, output vs temp)
±0.5% of span, (temp ³32°F/0°C)
±0.15% of span, (temp <32°F/0°C)
(others, output vs res)
±0.01% of span
Temperature Stability
±0.04% of span per °C
Common Mode Rejection
120 dB,DC to 60 Hz
Isolation (MM4001ISO)
Output/Input
>500 megohms
Breakdown Voltage
>1000 VAC rms
Output Ripple (peak-to-peak)
<0.1% of span
Breakdown, Pwr/Circuitry
>1500 VAC rms
Operating Temperature
14°F to 140°F / -10°C to 60°C
Temperature Stability
±0.02% of span or 0.025°C/°C,
whichever is greater
Power
115 VAC ±10%, 50 or 60 Hz
(2.5 W max)
230 VAC ±10%, 50 or 60 Hz
(2.5 W max)
(DC Power Option)
24 VDC (limits 21 VDC to 32 VDC)
(2.5 W max)
Isolation, DC power supply to input
common: 10 megohms
Specifications are subject to change without notice. © 2007 Wilkerson Instrument Co., Inc
DWG#W102234B 3/07
34


Part Number MM4001
Description RTD INPUT TRANSMITTERS
Maker WICI
Total Page 2 Pages
PDF Download

MM4001 Datasheet PDF

View PDF for Mobile








Similar Datasheet

1 MM4000 PNP SILICON TRANSISTOR
Central Semiconductor
2 MM4000 GENERAL PURPOSE TRANSISTOR
Motorola
3 MM4001 PNP SILICON TRANSISTOR
Central Semiconductor
4 MM4001 GENERAL PURPOSE TRANSISTOR
Motorola
5 MM4001 RTD INPUT TRANSMITTERS
WICI
6 MM4001ISO RTD INPUT TRANSMITTERS
WICI
7 MM4002 PNP SILICON TRANSISTOR
Central Semiconductor
8 MM4002 GENERAL PURPOSE TRANSISTOR
Motorola
9 MM4003 PNP SILICON TRANSISTOR
Central Semiconductor





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy