TPS75101ĆEP, '75115ĆEP, '75118ĆEP, '75125ĆEP, '75133ĆEP WITH POWER GOOD
TPS75301ĆEP, TPS75315ĆEP, TPS75318ĆEP, TPS75325ĆEP, TPS75333ĆEP WITH RESET
FASTĆTRANSIENTĆRESPONSE 1.5ĆA LOWĆDROPOUT VOLTAGE REGULATORS
SGLS158 − APRIL 2003
D Controlled Baseline
− One Assembly/Test Site, One Fabrication
D Enhanced Diminishing Manufacturing
Sources (DMS) Support
D Enhanced Product Change Notification
D Qualification Pedigree†
D 1.5-A Low-Dropout Voltage Regulator
D Available in 1.5-V, 1.8-V, 2.5-V, 3.3-V, Fixed
Output and Adjustable Versions
D Open Drain Power-Good (PG) Status
D Open Drain Power-On Reset With 100-ms
D Dropout Voltage Typically 160 mV at 1.5 A
† Component qualification in accordance with JEDEC and industry
standards to ensure reliable operation over an extended
temperature range. This includes, but is not limited to, Highly
Accelerated Stress Test (HAST) or biased 85/85, temperature
cycle, autoclave or unbiased HAST, electromigration, bond
intermetallic life, and mold compound life. Such qualification
testing should not be viewed as justifying use of this component
beyond specified performance and environmental limits.
D Ultralow 75 µA Typical Quiescent Current
D Fast Transient Response
D 2% Tolerance Over Specified Conditions
For Fixed-Output Versions
D 20-Pin TSSOP (PWP) PowerPAD Package
D Thermal Shutdown Protection
PG or RESET†
NC − No internal connection
† PG is on the TPS751xx and RESET is on the TPS753xx
The TPS753xxQ and TPS751xxQ are low dropout regulators with integrated power-on reset and power-good (PG)
functions respectively. These devices are capable of supplying 1.5 A of output current with a dropout of 160 mV
(TPS75133Q, TPS75333Q). Quiescent current is 75 µA at full load and drops down to 1 µA when the device is
disabled. TPS751xxQ and TPS753xxQ are designed to have fast transient response for larger load current
Because the PMOS device behaves as a low-value resistor, the dropout voltage is very low (typically 160 mV at an
output current of 1.5 A for the TPS75x33Q) and is directly proportional to the output current. Additionally, since the
PMOS pass element is a voltage-driven device, the quiescent current is very low and independent of output loading
(typically 75 µA over the full range of output current, 1 mA to 1.5 A). These two key specifications yield a significant
improvement in operating life for battery-powered systems.
The device is enabled when EN is connected to a low level voltage. This LDO family also features a sleep mode;
applying a TTL high signal to EN (enable) shuts down the regulator, reducing the quiescent current to less than 1
µA at TJ = 25°C.
For the TPS751xxQ, the power-good terminal (PG) is an active high, open drain output, which can be used to
implement a power-on reset or a low-battery indicator.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Copyright 2003, Texas Instruments Incorporated
•POST OFFICE BOX 655303 DALLAS, TEXAS 75265