900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf






pickering

104-1-A-12-1D Datasheet Preview

104-1-A-12-1D Datasheet

High Voltage SIL/SIP Reed Relays

No Preview Available !

Pickering Series 104
High Voltage SIL/SIP Reed Relays
Up to 3 kilovolts Stand-off
Stacking on 0.25 inches pitch
Features
zz Small size
zz Internal mu-metal magnetic screen
zz One or two switches in a single package
zz Form A (energise to make) or Form B (energise to break)
configurations
zz Dry and mercury wetted switches available
zz 3, 5, 12 and 24 Volt coils with or without internal diode
zz 100% tested for dynamic contact resistance for guaranteed
performance
The Series 104 is a range of Single-In-Line reed relays intended for
voltages that are beyond the capabilities of conventional SIL reed
relays.
They are ideal for such applications as transformer or cable testing
or any other automatic test equipment where high voltages are
involved.
Where mains voltages are switched, for example to control and
isolate S.C.R. or triac gates, they are an ideal choice.
One or two Form A (energize to make) or one Form B (energize to
break) configurations are available.
The range features an internal mu-metal screen to eliminate
problems that would otherwise be experienced due to magnetic
interaction when they are closely stacked.
Three types of dry switches are available, capable of standing-off
1, 1.5 or 3kV d.c. The 3kV version has an increased clearance
between the switch and coil pins to accommodate the higher
voltage. Even higher voltage ratings are available to special order,
please contact our sales office for further information.
Mercury wetted devices are also available for applications where
bounce free switching is required. These are rated at 1500 volts d.c.
stand-off, 500 volts d.c. switching at up to 50 watts.
Switch Ratings - Dry switches
zz 1 or 2 Form A (energize to make)
1000 Volts d.c. stand-off
500 Volts d.c. switching at 10 Watts
zz 1 or 2 Form A (energize to make)
1500 Volts d.c. stand-off
1000 Volts d.c. switching at 10 Watts
zz 1 Form A (energize to make)
3000 Volts d.c. stand-off
1000 Volts d.c. switching at 25 Watts
zz 1 Form B (energize to break)
1000 Volts d.c. stand-off
500 Volts d.c. switching at 10 Watts
zz 1 Form B (energize to break)
1500 Volts d.c. stand-off
1000 Volts d.c. switching at 10 Watts
Switch Ratings - Mercury switches
zz 1 or 2 Form A (energize to make)
1500 Volts d.c. stand-off
500 Volts d.c. switching at 50 Watts
email: sales@pickeringrelay.com
pickeringrelay.com
104/07/17




pickering

104-1-A-12-1D Datasheet Preview

104-1-A-12-1D Datasheet

High Voltage SIL/SIP Reed Relays

No Preview Available !

Series 104 switch ratings - The contact ratings for each switch type are shown below:
Switch Switch
No form
1 A or B
2 A or B
3A
Power
rating
10 W
10 W
25 W
Max.
switch
current
0.50 A
0.50 A
1.00 A
Max.
carry
current
1.0 A
1.0 A
1.5 A
Max.
switching
volts
500
1000
1000
Max.
stand-off
volts
1000
1500
3000
Life expectancy
ops typical
(see Note1 below)
10E8
10E8
10E8
Operate time
inc bounce
(max)
1.0 ms
1.0 ms
1.0 ms
Release
time
0.3 ms
0.3 ms
0.3 ms
Coil data and type numbers
Device
type
Max. Insulation resistance Capacitance (typical)
Type Number
Coil Coil
contact
(V) resistance resistance
(minimum)
(see Note2 below)
Switch Across Closed switch Across
(initial)
to coil switch
to coil open switch
1 Form A (energize to make)
Switch No. 1 (1kV)
104-1-A-5/1D
104-1-A-12/1D
104-1-A-24/1D
5
12
24
375 Ω
1000 Ω
3000 Ω
0.15 Ω
10E12 Ω 10E12 Ω
2.5 pF
0.1 pF
1 Form A (energize to make)
Switch No. 2 (1.5kV)
104-1-A-5/2D
104-1-A-12/2D
104-1-A-24/2D
5
12
24
375 Ω
1000 Ω
3000 Ω
0.15 Ω
10E12 Ω 10E12 Ω
2.5 pF
0.1 pF
1 Form A (energize to make)
Switch No. 3 (3.0kV)
104-1-A-5/3D
104-1-A-12/3D
104-1-A-24/3D
5
12
24
220 Ω
500 Ω
3000 Ω
0.15 Ω
10E12 Ω 10E12 Ω
2.5 pF
0.1 pF
1 Form B (energize to break)
Switch No. 1 (1kV)
104-1-B-5/1D
104-1-B-12/1D
104-1-B-24/1D
5
12
24
750 Ω
2000 Ω
3000 Ω
0.20 Ω
10E12 Ω 10E12 Ω
2.5 pF
0.1 pF
1 Form B (energize to break)
Switch No. 2 (1.5kV)
104-1-B-5/2D
104-1-B-12/2D
104-1-B-24/2D
5
12
24
750 Ω
2000 Ω
3000 Ω
0.20 Ω
10E12 Ω 10E12 Ω
2.5 pF
0.1 pF
2 Form A (energize to make)
Switch No. 1 (1kV)
104-2-A-5/1D
104-2-A-12/1D
104-2-A-24/1D
5
12
24
250 Ω
750 Ω
2000 Ω
0.20 Ω
10E12 Ω 10E12 Ω
See
Note3
See
Note3
2 Form A (energize to make)
Switch No. 2 (1.5kV)
104-2-A-5/2D
104-2-A-12/2D
104-2-A-24/2D
5
12
24
250 Ω
750 Ω
2000 Ω
0.20 Ω
10E12 Ω 10E12 Ω
See
Note3
See
Note3
When an internal diode is required, the suffix D is added to the part number as shown in the table.
Mercury Reed: Series 104 switch ratings - The contact ratings for each switch type are shown below:
Switch Switch
No form
6A
Power
rating
50 W
Max.
switch
current
2.00 A
Max.
carry
current
3.00 A
Max.
switching
volts
500
Max.
stand-off
volts
1500
Life expectancy
ops typical
(see Note1 below)
10E8
Operate time
(max)
1.5 ms
Release
time
1.0 ms
Mercury Relay: Coil data and type numbers
Device
type
Max. Insulation resistance Capacitance (typical)
Type Number
Coil
(V)
Coil
resistance
contact
resistance
(minimum)
(see Note2 below)
Switch Across Closed switch Across
(initial)
to coil switch
to coil open switch
1 Form A (energize to make)
Switch No. 6 (1.5kV)
104-1-A-5/6D
104-1-A-12/6D
104-1-A-24/6D
5
12
24
100 Ω
500 Ω
1500 Ω
0.12 Ω
10E12 Ω 10E11 Ω
3 pF
0.1 pF
2 Form A (energize to make)
Switch No. 6 (1.5KV)
104-2-A-5/6D
104-2-A-12/6D
104-2-A-24/6D
5
12
24
50 Ω
275 Ω
1000 Ω
0.15 Ω
10E12 Ω 10E11 Ω
See
Note3
See
Note3
When an internal diode is required, the suffix D is added to the part number as shown in the table.
Note1 Life expectancy
The life of a reed relay depends upon the switch load and end of life criteria. For example, for an ‘end of life’ contact resistance
specification of 1 Ω, switching low loads (10 V at 10 mA resistive) or when ‘cold’ switching, typical life is approx 1 x 108 ops. At the
maximum load (resistive), typical life is 1 x 107 ops. In the event of abusive conditions, e.g. high currents due to capacitive inrushes,
this figure reduces considerably. Pickering will be pleased to perform life testing with any particular load condition.
Note2 Capacitance across open switch
The capacitance across the open switch was measured with other connections guarded.
Note3 Capacitance values
The value will depend upon on the mode of connection/guarding of unused terminals. Please contact technical sales for details.
Mercury Relays
Mercury relays should be mounted vertically with pin 1 uppermost. Pin 1 is marked with a bar on the top face of the
relay.
Internal Mu-metal Magnetic Screen
The Series 104 relays are fitted with an internal mu-metal magnetic screen which permits side-by-side stacking.
Main contact:
UK Headquarters: email: sales@pickeringrelay.com | Tel. +44 1255 428141
Worldwide contacts:
USA: email: ussales@pickeringtest.com | Tel. +1 781 897 1710
Germany: email: desales@pickeringtest.com | Tel. +49 89 125 953 160
China: email: johnson@tomtech.cn | Tel. 0755 8374 5452
For a full list of agents and representatives visit: pickeringrelay.com/agents
ISO9001 Manufacture of
Reed Relays FM 29036
Pin Configuration and Dimensional Data
Dimensions in Inches (Millimeters in brackets)
0.95 (24.1)
0.245
(6.22)
Pin 1
0.02
(0.51)
0.01
(0.25)
0.32
(8.13)
0.125
(3.175)
0.02
(0.51)
+
1357
1 Form A (Energize to make)
Switch No. 1 (1 kV stand-off)
Switch No. 2 (1.5 kV stand-off)
Switch No. 6 (Mercury Wetted)
Pin 1
0.95 (24.1)
0.245
(6.22)
0.02
(0.51)
0.01
(0.25)
0.32
(8.13)
0.125
(3.175)
0.02
(0.51)
+
1357
1 Form A (Energize to make)
Switch No. 3 (3 kV stand-off)
1.14 (29)
0.245
(6.22)
0.49
(12.5)
Pin 1
0.02 0.01
(0.51) (0.25)
0.125
(3.175)
0.02
(0.51)
+
12 3
456
2 Form A (Energize to make)
Switch No. 1 (1 kV stand-off)
Switch No. 2 (1.5 kV stand-off)
Switch No. 6 (Mercury Wetted)
1.14 (29)
0.245
(6.22)
0.49
(12.5)
Pin 1
0.02
(0.51)
0.01
(0.25)
0.125
(3.175)
0.02
(0.51)
1 Form B (Energize to break)
Switch No. 1 (1 kV stand-off)
+ Switch No. 2 (1.5 kV stand-off)
1357
Important: Where the optional internal diode is fitted or for all Form B
types, the correct coil polarity must be observed, as shown by the
+ symbol on the schematics.
3D Models: Interactive models of the complete range of
Pickering relay products can be downloaded from the web site.
Order Code
104 - 1 - A - 5 / 2 D
Series
Number of reeds
Switch form
Coil voltage
Switch number (See table adjacent)
Diode if fitted (Omit if not required)
Help
If you need any technical advice or other help, for example,
any special tests that you would like carried out, please do
not hesitate to contact our Technical Sales Department. We
will always be pleased to discuss Pickering relays with you.
email: techsales@pickeringrelay.com
Please ask us for a FREE evaluation sample.
pickeringrelay.com


Part Number 104-1-A-12-1D
Description High Voltage SIL/SIP Reed Relays
Maker pickering
Total Page 2 Pages
PDF Download

104-1-A-12-1D Datasheet PDF

View PDF for Mobile








Similar Datasheet

1 104-1-A-12-1D High Voltage SIL/SIP Reed Relays
pickering





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy