900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Atmel Electronic Components Datasheet

AT91SAM7L64 Datasheet

Microcontroller

No Preview Available !

Features
Incorporates the ARM7TDMI® ARM® Thumb® Processor
– High-performance 32-bit RISC Architecture
– High-density 16-bit Instruction Set
– Leader in MIPS/Watt
– EmbeddedICEIn-circuit Emulation, Debug Communication Channel Support
Internal High-speed Flash
– 128 Kbytes (AT91SAM7L128), Organized in 512 Pages of 256 Bytes Single Plane
– 64 Kbytes (AT91SAM7L64), Organized In 256 Pages of 256 Bytes Single Plane
– Single Cycle Access at Up to 15 MHz in Worst Case Conditions
– 128-bit Read Access
– Page Programming Time: 4.6 ms, Including Page Auto Erase, Full Erase Time: 10 ms
– 10,000 Write Cycles, 10-year Data Retention Capability, Sector Lock Capabilities,
Flash Security Bit
– Fast Flash Programming Interface for High Volume Production
Internal High-speed SRAM, Single-cycle Access at Maximum Speed
– 6 Kbytes
• 2 Kbytes Directly on Main Supply That Can Be Used as Backup SRAM
• 4 Kbytes in the Core
Memory Controller (MC)
– Enhanced Embedded Flash Controller, Abort Status and Misalignment Detection
Enhanced Embedded Flash Controller (EEFC)
– Interface of the Flash Block with the 32-bit Internal Bus
– Increases Performance in ARM and Thumb Mode with 128-bit Wide Memory
Interface
Reset Controller (RSTC)
– Based on Zero-power Power-on Reset and Fully Programmble Brownout Detector
– Provides External Reset Signal Shaping and Reset Source Status
Clock Generator (CKGR)
– Low-power 32 kHz RC Oscillator, 32 kHz On-chip Oscillator, 2 MHz Fast RC
Oscillator and one PLL
Supply Controller (SUPC)
– Minimizes Device Power Consumption
– Manages the Different Supplies On Chip
– Supports Multiple Wake-up Sources
Power Management Controller (PMC)
– Software Power Optimization Capabilities, Including Active and Four Low Power
Modes:
• Idle Mode: No Processor Clock
• Wait Mode: No Processor Clock, Voltage Regulator Output at Minimum
• Backup Mode: Voltage Regulator and Processor Switched Off
• Off (Power Down) Mode: Entire Chip Shut Down Except for Force Wake Up Pin
(FWUP) that Re-activates the Device. 100 nA Current Consumption.
In Active Mode, Dynamic Power Consumption <30 mA at 36 MHz
– Three Programmable External Clock Signals
– Handles Fast Start Up
AT91 ARM
Thumb-based
Microcontroller
AT91SAM7L128
AT91SAM7L64
Preliminary
.
6257A–ATARM–20-Feb-08


Atmel Electronic Components Datasheet

AT91SAM7L64 Datasheet

Microcontroller

No Preview Available !

Advanced Interrupt Controller (AIC)
– Individually Maskable, Eight-level Priority, Vectored Interrupt Sources
– Two External Interrupt Sources and One Fast Interrupt Source, Spurious Interrupt Protected
Debug Unit (DBGU)
– Two-wire UART and Support for Debug Communication Channel interrupt, Programmable ICE Access Prevention
Periodic Interval Timer (PIT)
– 20-bit Programmable Counter plus 12-bit Interval Counter
Windowed Watchdog (WDT)
– 12-bit Key-protected Programmable Counter
– Provides Reset or Interrupt Signals to the System
– Counter may be Stopped While the Processor is in Debug State or in Idle Mode
Real-time Clock (RTC)
– Two Hundred Year Calendar with Alarm
– Runs Off the Internal RC or Crystal Oscillator
Three Parallel Input/Output Controllers (PIOA, PIOB, PIOC)
– Eighty Programmable I/O Lines Multiplexed with up to Two Peripheral I/Os
– Input Change Interrupt Capability on Each I/O Line
– Individually Programmable Open-drain, Pull-up resistor and Synchronous Output
Eleven Peripheral DMA Controller (PDC) Channels
One Segment LCD Controller
– Display Capacity of Forty Segments and Ten Common Terminals
– Software Selectable LCD Output Voltage (Contrast)
Two Universal Synchronous/Asynchronous Receiver Transmitters (USART)
– Individual Baud Rate Generator, IrDA® Infrared Modulation/Demodulation
– Support for ISO7816 T0/T1 Smart Card, Hardware Handshaking, RS485 Support
– Manchester Encoder/Decoder
– Full Modem Line Support on USART1
One Master/Slave Serial Peripheral Interface (SPI)
– 8- to 16-bit Programmable Data Length, Four External Peripheral Chip Selects
One Three-channel 16-bit Timer/Counter (TC)
– Three External Clock Inputs, Two Multi-purpose I/O Pins per Channel
– Double PWM Generation, Capture/Waveform Mode, Up/Down Capability
One Four-channel 16-bit PWM Controller (PWMC)
One Two-wire Interface (TWI)
– Master, Multi-Master and Slave Mode Support, All Atmel® Two-wire EEPROMs and I2C compatible Devices Supported
– General Call Supported in Slave Mode
One 4-channel 10-bit Analog-to-Digital Converter, Four Channels Multiplexed with Digital I/Os
SAM-BA® Boot Assistant
– Default Boot Program
– Interface with SAM-BA Graphic User Interface
– In Application Programming Function (IAP)
IEEE® 1149.1 JTAG Boundary Scan on All Digital Pins
Four High-current Drive I/O lines, Up to 4 mA Each
Power Supplies
– Embedded 1.8V Regulator, Drawing up to 60 mA for the Core with Programmable Output Voltage
– Single Supply 1.8V - 3.6V
Fully Static Operation: Up to 36 MHz at 85°C, Worst Case Conditions
Available in a 128-lead LQFP Green and a 144-ball LFBGA Green Package
2 AT91SAM7L128/64 Preliminary
6257A–ATARM–20-Feb-08


Part Number AT91SAM7L64
Description Microcontroller
Maker ATMEL Corporation
PDF Download

AT91SAM7L64 Datasheet PDF






Similar Datasheet

1 AT91SAM7L64 Microcontroller
ATMEL Corporation





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy