900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf






Emerson

NTS505-M Datasheet Preview

NTS505-M Datasheet

AC-DC / 261W - 500W Medical

No Preview Available !

Embedded Power for
Business-Critical Continuity
NTS500-M Series
500 Watts
Medical
Total Power:
Input Voltage:
# of Outputs:
200 - 500 Watts
85 - 264 Vac
120 - 300 Vdc
Single
Rev. 09.8.09_#99
NTS500-M Series
 of 3
Special Features
• Active power factor correction
• IEC EN61000-3-2 compliance
• Remote sense
• Power fail and remote inhibit
• Single wire current sharing
• Built-in EMI filter
• Low output ripple
• 5V standby
• 12V fan output
• Overvoltage protection
• Overload protection
• Thermal overload protection
• DC power good
• Built in OR-ing diode / FET
• Optional fan cover (-CF suffix)
• PM Bus compliant
• Digital I2C interface
• 2 year warranty
Electrical Specifications
Input
Input ra­nge:
Frequency:
Inrush current:
Efficiency:
EMI filter:
Safety ground leakage
current:
85 - 264 Vac (wide range)
47 - 63 Hz
50 A max., cold start @ 25 °C
85% typical at full load, nominal line
FCC Class B conducted and radiated; CISPR22 Class B conducted and
radiated; EN55022 Class B conducted and radiated; VDE0878PT3 Class B
conducted and radiated.
< 0.3 mA @ 50/60 Hz, 264 Vac input
Output
Maximum power:
Adjustment range:
Standby output:
Fan output:
Hold-up time:
Overload protection:
Overvoltage protection:
200 W for convection; 500 W with 30 CFM forced air
± 5%
5 V @ 1 A convection, 2 A forced air, regulated, ±5%
12 V @ 1 A, -5 %, +7%, 0.5 A for -CF version
20 ms @ 500 W load, 115 VAC nominal line at factory voltage setting
Short circuit protection on all outputs. Case overload protected @
115 - 130% above peak rating
20 - 35% above nominal output
Safety
TUV:
cCSAus:
CB:
CE:
60601-1
60601-1
Certificate & report
Mark (LVD)




Emerson

NTS505-M Datasheet Preview

NTS505-M Datasheet

AC-DC / 261W - 500W Medical

No Preview Available !

Embedded Power for
Business-Critical Continuity
Logic Control
Power failure:
Remote on/off:
DC OK:
Remote sense:
TTL logic signal goes high 100 - 500 msec after main output. It goes
low at least 4 msec before loss of regulation
Requires an external contact closure to inhibit outputs
TTL logic goes high after the output is in regulation. It goes low when
there is loss of regulation.
Compensates for 0.5 V lead drop min. Will operate without remote
sense connected. Reverse connection protected.
Environmental Specifications
Operating temperature:
Storage temperature:
Electromagnetic
susceptibility:
Humidity:
Vibration:
0° to 50 °C ambient derate each output as 2.5% per degree from
50° to 70 °C.
-40 °C to +85 °C
designed to meetEN61000-4;
-2, -3, -4, -5, -6, -8, -11 Level 3
Operating; non-condensing 10% to 90% RH
Three orthogonal axes, sweep at
1 oct/min, 5 min. dwell at four major resonances
2 G peak 8 Hz to 500 Hz, operational
Ordering Information
Model
Number
Output Minimum
Voltage Load
Maximum Load
with Convection
Cooling
Maximum
Load with
30CFM Forced
Air
Peak
Load1
Regulation2
Ripple
P/P (PARD)3
NTS503-M 12 V
0A
16.6 A
41.7 A 47 A ±2% 120 mV
NTS505-M 24 V
0A
8.3 A
20.8 A
23.4 A
±2%
240 mV
NTS508-M 48 V
0A
4.2 A
10.4 A
11.7 A
±2%
480 mV
1. Peak current lasting < 30 seconds with a maximum 10% duty cycle.
2­. At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory
settings.
3­. Peak-to-peak with 20 MHz bandwidth and 10 µF (tantalum capacitor) in parallel with a 0.1 µF capacitor
at rated line voltage and load ranges.
4. 12 V fan output cannot be used above 50 °C with convection cooling.
Rev. 09.8.09_#99
NTS500-M Series
 of 3
Pin Assignments
Connector
CN1
PIN 1 Line
PIN 3 Neutral
PIN 5 Ground
SK7 PIN 1 V1 swp
1 5 PIN 2 - Remote Sense
PIN 3 + Remote Sense
6 10 PIN 4 5 VSB (standby)
PIN 5 5 VSB return
PIN 6 +12 V
PIN 7 Common
PIN 8 Inhibit
PIN 9 DC power good (DC OK)
PIN 10 Power Fail (POK)
SK8
PIN 1 +12 V Fan
PIN 2 Common
CN403 PIN 1 5 V_I2C
1 5 PIN 2 Ground
PIN 3 A2
6 10 PIN 4 A0
PIN 5 SVCC2_OR
PIN 6 I2C_SDA
PIN 7 I2C_SLC
PIN 8 A1
PIN 9 N/C
PIN 10 +12 V_RTN_CTRL
Adjustment Potentiometers
P1 +V1 Output adjust
Mating Connectors
SK4,5,6 Molex 19141-0058
SK7 Control Molex 90142-0010
signals PINS: 90119-2110
or
Amp: 87977-3
PINS: 87309-8
SK8 JST PHR-2
Pins: SPH-002T-PO.5S
CN403
JST PHDR-10VS
Pins: JST 5PHD-002T-PO.5-L/P or
Landwin 2050 S1000
Pins: 2053T011P
Emerson Connector Kit #70-841-024 includes all of
the above
Notes:
1. Specifications subject to change without notice.
2. All dimensions in inches (mm), tolerance is ±.02”.
3. Specifications are at factory settings
4. Mounting maximum insertion depth is 0.12”.
5. Warranty: 2 year
6. Weight: 3.016 lb. / 1.18 kg.


Part Number NTS505-M
Description AC-DC / 261W - 500W Medical
Maker Emerson
Total Page 3 Pages
PDF Download

NTS505-M Datasheet PDF

View PDF for Mobile








Similar Datasheet

1 NTS505-M AC-DC / 261W - 500W Medical
Emerson





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy