900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




International Rectifier Electronic Components Datasheet

M3G280512T Datasheet

HYBRID-HIGH RELIABILITY RADIATION HARDENED DC-DC CONVERTER

No Preview Available !

PD-94535P
HYBRID-HIGH RELIABILITY
RADIATION HARDENED
DC-DC CONVERTER
M3G-SERIES
28V Input, Triple Output
Description
The M3G-Series of DC-DC converters are radiation
hardened, high reliability converters designed for
extended operation in hostile environments. Their small
size and low weight make them ideal for applications
such as geostationary earth orbit satellites and deep
space probes. They exhibit a high tolerance to total
ionizing dose, single event effects and environmental
stresses such as temperature extremes, mechanical
shock, and vibration.
The converters incorporate a fixed frequency single
ended forward topology with magnetic feedback and
an internal EMI filter that utilizes multilayer ceramic
capacitors that are subjected to extensive lot screening
for optimum reliability. These converters are capable
of meeting the conducted emissions and conducted
susceptibility requirements of MIL-STD-461C without
any additional components. External inhibit and
synchronization input and output allow these converters
to be easily incorporated into larger power systems.
They are enclosed in a hermetic 3" x 2" x 0.475" package
constructed of an Aluminum-Silicon-Carbide (AlSiC)
base and an Alloy 48 ring frame and they weigh less
than 110 grams. The package utilizes rugged ceramic
feed-through copper core pins and is sealed using
parallel seam welding.
Manufactured in a facility fully qualified to MIL-PRF-
38534, these converters are fabricated utilizing DLA
Land and Maritime qualified processes. For available
screening options, refer to device screening table in the
data sheet.
Non-flight versions of the M3G-Series converters are
available for system development purposes. Variations
in electrical specifications and screening to meet custom
requirements can be accommodated.
M3G
Features
n Total Dose > 200 krad(Si),
typically usable to > 300 krad(Si)
.n SEE Hardened up to 82 MeV cm2/mg
n Internal EMI filter; Converter Capable of
meeting MIL-STD-461C CE03
n Low Weight, < 110 grams
n Magnetically Coupled Feedback
n 18V to 50V DC Input Range
n Up to 40W Output Power
n Triple Output Models Include
+5V and ±12V or ±15V
n Main Output Isolated from Dual Outputs
n High Efficiency - to 80%
n -55°C to +125°C Operating Temperature Range
n 100M@ 500VDC Isolation
n Under-Voltage Lockout
n Synchronization Input and Output
n Short Circuit and Overload Protection
n Output Over Voltage Limiter
n External Inhibit
n > 5,000,000 Hour MTBF
n Standard Microcircuit Drawings Available
Applications
n Geostationary Earth Orbit Satellites (GEO)
n Deep Space Satellites / Probes
n Strategic Weapons and Communication
Systems
www.irf.com
1
09/11/12
http://www.Datasheet4U.com


International Rectifier Electronic Components Datasheet

M3G280512T Datasheet

HYBRID-HIGH RELIABILITY RADIATION HARDENED DC-DC CONVERTER

No Preview Available !

M3G-SERIES
(28V Input, Triple Output)
Circuit Description
The M3G-Series converters utilize a single-ended
forward topology with resonant reset. The nominal
switching frequency is 500kHz. Electrical isolation
and tight output regulation are achieved through the
use of a magnetically coupled feedback. Voltage
feed-forward with duty factor limiting provides high
line rejection and protection against output over
voltage in the event of an internal control loop failure.
This mechanism limits the maximum output voltage
to approximately 20% over the nominal regardless of
the line voltage.
An internal EMI filter allows the converter to meet the
conducted emissions requirements of MIL-STD-461C
on the input power leads. A two-stage output filter
reduces the typical output ripple to less than 20mV
peak-to-peak.
The main ( +5 volt ) output is regulated by the control
loop and typically exhibits better than 1% regulation.
The auxiliary ( ±12 volt or ±15 volt ) outputs are
maintained through tight coupling in the power
transformer and main output filter inductor and
typically exhibit better than 5% regulation. The main
output and auxiliary outputs are isolated from each
other.
Output power is limited under any load fault condition
to approximately 125% of rated. An overload
condition causes the converter output to behave like
a constant current source with the output voltage
dropping below nominal. The converter will resume
normal operation when the load current is reduced
below the current limit point. This protects the
converter from both overload and short circuit
conditions. The current limit point exhibits a slightly
negative temperature coefficient to reduce the
possibility of thermal runaway.
An under-voltage lockout circuit prohibits the
converter from operating when the line voltage is too
low to maintain the output voltage. The converter will
not start until the line voltage rises to approximately
16.5 volts and will shut down when the input voltage
drops below 15.5 volts. The one volt of hysteresis
reduces the possibility of line noise interfering with
the converter’s start-up and shut down.
An external inhibit port is provided to control converter
operation. The nominal threshold relative to the input
return (pin 2) is 1.4V. If 2.0 volts or greater are applied
to the Inhibit pin (pin 3) then the converter will
operate normally. A voltage of 0.8V or less will cause
the converter to shut-down. The pin may be left
open for normal operation and has a nominal open
circuit voltage of 4.0V.
Synchronization input and output allow multiple
converters to operate at a common switching
frequency. Converters can be synchronized to one
another or to an externally provided clock. This can
be used to eliminate beat frequency noise or to avoid
creating noise at certain frequencies for sensitive
systems.
Design Methodology
The M3G-Series was developed using a proven
conservative design methodology which includes
selecting radiation tolerant and established reliability
components and fully derating to the requirements
of MIL-STD-975 and MIL-STD-1547 except for the
CDR type ceramic capacitors, a capacitor with 50V
rating is used for in-circuit voltage stress of less than
10V. Careful sizing of decoupling capacitors and
current limiting resistors minimizes the possibility of
photo-current burn-out. Heavy derating of the
radiation hardened power MOSFET virtually
eliminates the possibility of SEGR and SEB. A
magnetic feedback circuit is utilized instead of opto-
couplers to minimize temperature, radiation and
aging sensitivity. PSPICE and RadSPICE were used
extensively to predict and optimize circuit
performance for both beginning and end-of-life.
Thorough design analyses include Radiation
Susceptibility (TREE ), Worst Case, Stress, Thermal,
Failure Modes and Effects (FMEA) and Reliability
(MTBF).
2 www.irf.com
http://www.Datasheet4U.com


Part Number M3G280512T
Description HYBRID-HIGH RELIABILITY RADIATION HARDENED DC-DC CONVERTER
Maker IRF
Total Page 13 Pages
PDF Download

M3G280512T Datasheet PDF

View PDF for Mobile








Similar Datasheet

1 M3G280512T HYBRID-HIGH RELIABILITY RADIATION HARDENED DC-DC CONVERTER
IRF





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy