900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Maxim Integrated Semiconductor Electronic Components Datasheet

MAX9952 Datasheet

(MAX9951 / MAX9952) Dual Per-Pin Parametric Measurement Units

No Preview Available !

MAX9951/MAX9952
Dual Per-Pin Parametric
Measurement Units
General Description
The MAX9951/MAX9952 dual parametric measurement
units (PMUs) feature a small package size, wide force and
measurement range, and high accuracy, making the
devices ideal for automatic test equipment (ATE) and other
instrumentation that requires a PMU per pin or per site.
The MAX9951/MAX9952 force or measure voltages in the
-2V to +7V through -7V to +13V ranges, dependent upon
the supply voltage (VCC and VEE). The devices handle
supply voltages of up to +30V (VCC to VEE) and a 20V
device-under-test (DUT) voltage swing at full current. The
MAX9951/MAX9952 also force or measure currents up to
±64mA with a lowest full-scale range of ±2µA. Integrated
support circuitry facilitates use of an external buffer ampli-
fier for current ranges greater than ±64mA.
A voltage proportional to the measured output voltage
or current is provided at the MSR_ output. Integrated
comparators, with externally set voltage thresholds,
provide detection for both voltage and current levels.
The MSR_ and comparator outputs can be placed in a
high-impedance state. Separate FORCE and SENSE
connections are short-circuit protected for voltages
from (VEE - 0.3V) to (VCC + 0.3V). The FORCE output
also features a low-leakage, high-impedance state.
Integrated voltage clamps limit the force output to lev-
els set externally. The force-current or the measure-cur-
rent voltage can be offset -0.2V to +4.4V (IOS). This
feature allows for the centering of the control or mea-
sured signal within the external DAC or ADC range.
The MAX9951D/MAX9952D feature an integrated 10kΩ
force-sense resistor between FORCE_ and SENSE_.
The MAX9951F/MAX9952F have no internal force-sense
resistor. These devices are available in a 64-pin, 10mm
x 10mm, 0.5mm pitch TQFP package with an exposed
8mm x 8mm die pad on the top (MAX9951) or the bot-
tom (MAX9952) of the package for efficient heat
removal. The exposed pad is internally connected to
VEE. The MAX9951/MAX9952 are specified over the
commercial 0°C to +70°C temperature range.
Memory Testers
VLSI Testers
System-on-a-Chip Testers
Structural Testers
Applications
Pin Configurations and Selector Guide appear at end of
data sheet.
Features
o Force Voltage/Measure Current (FVMI)
o Force Current/Measure Voltage (FIMV)
o Force Voltage/Measure Voltage (FVMV)
o Force Current/Measure Current (FIMI)
o Force Nothing/Measure Voltage (FNMV)
o Force Nothing/Measure Current (FNMI,
Range E Only)
o Termination/Measure Current
o Termination/Measure Voltage
o Five Programmable Current Ranges
±2µA
±20µA
±200µA
±2mA
±64mA
o -2V to +7V Through -7V to +13V Input-Voltage
Range
o Force-Current/Measure-Current Adjustable-
Voltage Offset (IOS)
o Programmable Voltage Clamps at Force Output
o Low-Leakage, High-Impedance Measure, and
Force States
o 3-Wire Serial Interface
o Low 6mA (max) Quiescent Current per PMU
Ordering Information
PART
TEMP RANGE PIN-PACKAGE
MAX9951DCCB+D
0°C to +70°C 64 TQFP-EPR*
MAX9951DCCB+TD
0°C to +70°C 64 TQFP-EPR*
MAX9951DCCB-D
0°C to +70°C 64 TQFP-EPR*
MAX9951DCCB-TD
0°C to +70°C 64 TQFP-EPR*
MAX9951FCCB+
0°C to +70°C 64 TQFP-EPR*
MAX9951FCCB+T
0°C to +70°C 64 TQFP-EPR*
MAX9951FCCB-D
0°C to +70°C 64 TQFP-EPR*
MAX9951FCCB-TD
0°C to +70°C 64 TQFP-EPR*
MAX9952DCCB+
0°C to +70°C 64 TQFP-EP**
MAX9952DCCB+T
0°C to +70°C 64 TQFP-EP**
MAX9952DCCB-D
0°C to +70°C 64 TQFP-EP**
MAX9952DCCB-TD
0°C to +70°C 64 TQFP-EP**
MAX9952FCCB+
0°C to +70°C 64 TQFP-EP**
MAX9952FCCB+T
0°C to +70°C 64 TQFP-EP**
MAX9952FCCB-D
0°C to +70°C 64 TQFP-EP**
MAX9952FCCB-TD
0°C to +70°C 64 TQFP-EP**
+Denotes a lead(Pb)-free/RoHS-compliant package.
-Denotes a package containing lead(Pb).
D = Dry pack.
*EPR = Top side exposed pad.
T = Tape and reel.
**EP = Exposed pad.
For pricing, delivery, and ordering information, please contact Maxim Direct
at 1-888-629-4642, or visit Maxim’s website at www.maximintegrated.com.
19-3247; Rev 6; 8/13


Maxim Integrated Semiconductor Electronic Components Datasheet

MAX9952 Datasheet

(MAX9951 / MAX9952) Dual Per-Pin Parametric Measurement Units

No Preview Available !

MAX9951/MAX9952
Dual Per-Pin Parametric
Measurement Units
ABSOLUTE MAXIMUM RATINGS
VCC to AGND .......................................................................+20V
VEE to AGND.........................................................................-15V
VCC to VEE ...........................................................................+32V
VL to AGND............................................................................+6V
AGND to DGND.....................................................-0.5V to +0.5V
Digital Inputs/Outputs ..................................-0.3V to (VL + 0.3V)
All Other Pins to AGND ....................(VEE - 0.3V) to (VCC + 0.3V)
Continuous Power Dissipation (TA = +70°C)
MAX9951_CCB (derate 125mW/°C above +70°C) ...10,000mW
MAX9952_CCB (derate 43.5mW/°C above +70°C) .....3478mW
θJA MAX9951_CCB (Note 1) ...........................................+8°C/W
θJC MAX9951_CCB (Note 1) ...........................................+2°C/W
θJA MAX9952_CCB (Note 1) .........................................+23°C/W
θJC MAX9952_CCB (Note 1) ...........................................+2°C/W
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Operating Temperature Range (commercial) ........0°C to +70°C
Lead Temperature (soldering, 10s) .................................+300°C
Soldering Temperature (reflow)
Lead(Pb)-Free Packages.............................................+260°C
Packages Containing Lead(Pb)......................................+240°C
Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer
board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(VCC = +12V, VEE = -7V, VL = +3.3V, TA = +25°C, unless otherwise noted. Specifications at TA = TMIN and TA = TMAX are guaranteed
by design and characterization. Typical values are at TA = +25°C, unless otherwise noted.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN TYP MAX UNITS
FORCE VOLTAGE
Force Input Voltage
Range
Forced Voltage
Input Bias Current
Forced-Voltage Offset
Forced-Voltage-Offset
Temperature Coefficient
VIN0_,
VIN1_
VDUT
VFOS
VEE + 2.5
DUT current at full scale
DUT current = 0A
VCC = +12V, VEE = -7V
VCC = +18V, VEE = -12V
-2
-7
VEE + 2.5
-25
±1
±100
VCC - 2.5 V
+7
+13
VCC - 2.5
+25
V
µA
mV
µV/°C
Forced-Voltage Gain
Error
VFGE Nominal gain of +1
-1
0.005
+1
%
Forced-Voltage-Gain
Temperature Coefficient
±10 ppm/°C
Forced-Voltage Linearity
Error
MEASURE CURRENT
Measure-Current Offset
Measure-Current-Offset
Temperature Coefficient
VFLER Gain and offset errors calibrated out (Notes 3, 4)
IMOS (Note 3)
-0.02
-1
+0.02 %FSR
+1 %FSR
±20 ppm/°C
Measure-Current Gain
Error
IMGE (Note 5)
-1 +1 %
Measure-Current-Gain
Temperature Coefficient
±20 ppm/°C
Linearity Error
IMLER
Gain and offset errors calibrated out
(Notes 3, 4, 6)
-0.02
+0.02 %FSR
2 Maxim Integrated


Part Number MAX9952
Description (MAX9951 / MAX9952) Dual Per-Pin Parametric Measurement Units
Maker Maxim Integrated Products
Total Page 24 Pages
PDF Download

MAX9952 Datasheet PDF

View PDF for Mobile








Similar Datasheet

1 MAX995 High-Speed / Micropower / Low-Voltage / SOT23 / Rail-to-Rail I/O Comparators
Maxim
2 MAX9950 (MAX9949 / MAX9950) Dual Per-Pin Parametric Measurement Units
Maxim Integrated Products
3 MAX9951 (MAX9951 / MAX9952) Dual Per-Pin Parametric Measurement Units
Maxim Integrated Products
4 MAX9952 (MAX9951 / MAX9952) Dual Per-Pin Parametric Measurement Units
Maxim Integrated Products





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy