900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Murata Manufacturing Electronic Components Datasheet

OKDY-T-40-W12-001-C Datasheet

40A Digital PoL DC-DC Converter

No Preview Available !

www.murata-ps.com
OKDx-T/40-W12-xxx-C
40A Digital PoL DC-DC Converter Series
PRELIMINARY
Typical units
FEATURES
Small package:
30.85 x 20.0 x 8.2 mm (1.215 x 0.787 x 0.323 in)
SIP: 33.0 x 7.6 x 18.1 mm (1.30 x 0.30 x 0.713 in)
0.6 V - 3.3 V output voltage range
High efficiency, typ. 97.2% at 5Vin, 3.3Vout half
load
Configuration and Monitoring via PMBus
Synchonization & phase spreading
Current sharing, Voltage Tracking & Voltage
margining
MTBF 14.2 Mh
PRODUCT OVERVIEW
Fully regulated
For narrow board pitch applications (15 mm/0.6 in)
Non-Linear Response for reduction of decoupling cap.
Input under voltage shutdown
Over temperature protection
Output short-circuit & Output over voltage protection
Remote control & Power Good
Voltage setting via pin-strap or PMBus
Configurable via Graphical User Interface
ISO 9001/14001 certified supplier
Highly automated manufacturing ensures quality
PART NUMBER STRUCTURE
OKD x - T / 40 - W12 - xxx - C
Digital Non-isolated PoL
Y = Surface Mount
H = Horizontal Mount Through-Hole
X = SIP
Trimmable Output
Voltage Range
0.6 - 3.3Vdc
RoHS Hazardous
Substance Compliance
C = RoHS-6 (does not claim EU RoHS exemption
7b – lead in solder)
Software Configuration Digits
(001 is positive turn-on logic)
Maximum Rated Output
Current in Amps
Input Voltage Range
4.5-14Vdc
For full details go to
www.murata-ps.com/rohs
www.murata-ps.com/support
PM
MDC_OKDx-T/40-W12-xxx-C.A01.D6 Page 1 of 40


Murata Manufacturing Electronic Components Datasheet

OKDY-T-40-W12-001-C Datasheet

40A Digital PoL DC-DC Converter

No Preview Available !

ORDERING GUIDE
Model Number
OKDY-T/40-W12-001-C
OKDH-T/40-W12-001-C
OKDX-T/40-W12-001-C
Output
0.6-3.3 V, 40 A/ 132 W
General Information
Reliability
The failure rate () and mean time between failures (MTBF= 1/) is
calculated at max output power and an operating ambient tempera-
ture (TA) of +40°C. Murata Power Modules uses Telcordia SR-332
Issue 2 Method 1 to calculate the mean steady-state failure rate and
standard deviation ().
Telcordia SR-332 Issue 2 also provides techniques to estimate
the upper confidence levels of failure rates based on the mean and
standard deviation.
Mean steady-state failure rate, Std. deviation,
71 nFailures/h
12.7 nFailures/h
MTBF (mean value) for the OKDx series = 14.2 Mh.
MTBF at 90% confidence level = 11.52 Mh
Compatibility with RoHS requirements
The products are compatible with the relevant clauses and require-
ments of the RoHS directive 2002/95/EC and have a maximum
concentration value of 0.1% by weight in homogeneous materials for
lead, mercury, hexavalent chromium, PBB and PBDE and of 0.01% by
weight in homogeneous materials for cadmium.
Exemptions in the RoHS directive utilized in Murata Power Solutions
products are found in the Statement of Compliance document.
Murata Power Solutions fulfills and will continuously fulfill all its
obligations under regulation (EC) No 1907/2006 concerning the regis-
tration, evaluation, authorization and restriction of chemicals (REACH)
as they enter into force and is through product materials declarations
preparing for the obligations to communicate information on sub-
stances in the products.
Quality Statement
The products are designed and manufactured in an industrial environ-
ment where quality systems and methods like ISO 9000, Six Sigma,
and SPC are intensively in use to boost the continuous improvements
strategy. Infant mortality or early failures in the products are screened
out and they are subjected to an ATE based final test. Conservative
design rules, design reviews and product qualifications, plus the high
competence of an engaged work force, contribute to the high quality
of the products.
Warranty
Warranty period and conditions are defined in Murata Power Solutions
General Terms and Conditions of Sale.
OKDx-T/40-W12-xxx-C
40A Digital PoL DC-DC Converter Series
PRELIMINARY
Limitation of Liability
Murata Power Solutions does not make any other warranties,
expressed or implied including any warranty of merchantability or
fitness for a particular purpose (including, but not limited to, use in life
support applications, where malfunctions of product can cause injury
to a person’s health or life)
The information and specifications in this technical specification is
believed to be correct at the time of publication. However, no liability
is accepted for inaccuracies, printing errors or for any consequences
thereof. Murata reserves the right to change the contents of this
technical specification at any time without prior notice.
Safety Specification
General information
Murata Power Solutions DC-DC converters and DC-DC regulators are
designed in accordance with safety standards IEC/EN/UL 60950 1
Safety of Information Technology Equipment.
IEC/EN/UL 60950 1 contains requirements to prevent injury or
damage due to the following hazards:
Electrical shock
Energy hazards
Fire
Mechanical and heat hazards
Radiation hazards
Chemical hazards
On-board DC-DC converters and DC-DC regulators are defined as
component power supplies. As components they cannot fully comply
with the provisions of any safety requirements without “Conditions of
Acceptability”. Clearance between conductors and between conduc-
tive parts of the component power supply and conductors on the
board in the final product must meet the applicable safety require-
ments. Certain conditions of acceptability apply for component power
supplies with limited stand-off (see Mechanical Information for further
information). It is the responsibility of the installer to ensure that the
final product housing these components complies with the require-
ments of all applicable safety standards and regulations for the final
product.
Component power supplies for general use should comply with the
requirements in IEC 60950 1, EN 60950 1 and UL 60950 1 Safety of
Information Technology Equipment.
There are other more product related standards, e.g. IEEE 802.3
CSMA/CD (Ethernet) Access Method, and ETS 300132 2 Power supply
interface at the input to telecommunications equipment, operated by
direct current (dc), but all of these standards are based on IEC/EN/UL
60950 1 with regards to safety.
Murata Power Solutions DC-DC converters and DC-DC regulators
are UL 60950 1 recognized and certified in accordance with EN 60950 1.
www.murata-ps.com/support
MDC_OKDx-T/40-W12-xxx-C.A01.D6 Page 2 of 40


Part Number OKDY-T-40-W12-001-C
Description 40A Digital PoL DC-DC Converter
Maker Murata
PDF Download

OKDY-T-40-W12-001-C Datasheet PDF






Similar Datasheet

1 OKDY-T-40-W12-001-C 40A Digital PoL DC-DC Converter
Murata





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy