900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




NXP Semiconductors Electronic Components Datasheet

PCU9654 Datasheet

8-bit UFm 5MHz I2C-bus 100mA 40V LED driver

No Preview Available !

PCU9654
8-bit UFm 5 MHz I2C-bus 100 mA 40 V LED driver
Rev. 1 — 2 July 2012
Product data sheet
1. General description
The PCU9654 is a UFm I2C-bus controlled 8-bit LED driver optimized for voltage switch
dimming and blinking 100 mA Red/Green/Blue/Amber (RGBA) LEDs. Each LED output
has its own 8-bit resolution (256 steps) fixed frequency individual PWM controller that
operates at 97 kHz with a duty cycle that is adjustable from 0 % to 99.6 % to allow the
LED to be set to a specific brightness value. An additional 8-bit resolution (256 steps)
group PWM controller has both a fixed frequency of 190 Hz and an adjustable frequency
between 24 Hz to once every 10.73 seconds with a duty cycle that is adjustable from 0 %
to 99.6 % that is used to either dim or blink all LEDs with the same value.
Each LED output can be off, on (no PWM control), set at its individual PWM controller
value or at both individual and group PWM controller values. The PCU9654 operates with
a supply voltage range of 2.3 V to 5.5 V and the 100 mA open-drain outputs allow
voltages up to 40 V for LED supply.
The PCU9654 is one of the first LED controller devices in a new Ultra Fast-mode (UFm)
family. UFm devices offer higher frequency (up to 5 MHz).
The active LOW Output Enable input pin (OE) blinks all the LED outputs and can be used
to externally PWM the outputs, which is useful when multiple devices need to be dimmed
or blinked together without using software control.
Software programmable LED Group and three Sub Call I2C-bus addresses allow all or
defined groups of PCU9654 devices to respond to a common I2C-bus address, allowing
for example, all red LEDs to be turned on or off at the same time, thus minimizing I2C-bus
commands. Six hardware address pins allow up to 64 devices on the same bus.
The Software Reset (SWRST) Call allows the master to perform a reset of the PCU9654
through the I2C-bus, identical to the Power-On Reset (POR) that initializes the registers to
their default state causing the outputs to be set HIGH (LED off). This allows an easy and
quick way to reconfigure all device registers to the same condition.


NXP Semiconductors Electronic Components Datasheet

PCU9654 Datasheet

8-bit UFm 5MHz I2C-bus 100mA 40V LED driver

No Preview Available !

NXP Semiconductors
PCU9654
8-bit UFm 5 MHz I2C-bus 100 mA 40 V LED driver
2. Features and benefits
8 LED drivers. Each output programmable at:
Off
On
Programmable LED brightness
Programmable group dimming/blinking mixed with individual LED brightness
5 MHz Ultra Fast-mode I2C-bus interface
256-step (8-bit) linear programmable brightness per LED output varying from fully off
(default) to maximum brightness using a 97 kHz PWM signal
256-step group brightness control allows general dimming (using a 190 Hz PWM
signal) from fully off to maximum brightness (default)
256-step group blinking with frequency programmable from 24 Hz to 10.73 s and duty
cycle from 0 % to 99.6 %
Eight open-drain outputs can sink between 0 mA to 100 mA and are tolerant to a
maximum off state voltage of 40 V. No input function.
Output state change programmable on the Acknowledge (bit 9, this bit is always set
to 1 by UFm I2C-bus master) or the STOP Command to update outputs byte-by-byte
or all at the same time (default to ‘Change on STOP’).
Active LOW Output Enable (OE) input pin allows for hardware blinking and dimming of
the LEDs when LED driver output state is fully ON (LDRx = 01 in LEDOUT0/1
registers)
Six hardware address pins allow 64 PCU9654 devices to be connected to the same
UFm I2C-bus and to be individually programmed
4 software programmable UFm I2C-bus addresses (one LED Group Call address and
three LED Sub Call addresses) allow groups of devices to be addressed at the same
time in any combination (for example, one register used for ‘All Call’ so that all the
PCU9654s on the I2C-bus can be addressed at the same time and the second register
used for three different addresses so that 13 of all devices on the bus can be
addressed at the same time in a group). Software enable and disable for I2C-bus
address.
Software Reset feature (SWRST Call) allows the device to be reset through the UFm
I2C-bus
25 MHz internal oscillator requires no external components
Internal power-on reset
Noise filter on USDA/USCL inputs
Glitch free LED outputs on power-up
Supports hot insertion
Low standby current
Operating power supply voltage (VDD) range of 2.3 V to 5.5 V
5.5 V tolerant inputs on non-LED pins
40 C to +85 C operation
ESD protection exceeds 2000 V HBM per JESD22-A114 and 1000 V CDM per
JESD22-C101
Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA
Packages offered: TSSOP24
PCU9654
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 2 July 2012
© NXP B.V. 2012. All rights reserved.
2 of 36


Part Number PCU9654
Description 8-bit UFm 5MHz I2C-bus 100mA 40V LED driver
Maker NXP
PDF Download

PCU9654 Datasheet PDF





Similar Datasheet

1 PCU9654 8-bit UFm 5MHz I2C-bus 100mA 40V LED driver
NXP
2 PCU9655 16-channel UFm 5MHz bus 100mA 40V LED driver
NXP
3 PCU9656 24-bit UFm 5MHz I2C-bus 100mA 40V LED driver
NXP





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy