900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




NXP Semiconductors Electronic Components Datasheet

UM10360 Datasheet

LPC17xx User manual

No Preview Available !

UM10360
LPC176x/5x User manual
Rev. 4. 1 — 19 December 2016
User manual
Document information
Info Content
Keywords
LPC1769, LPC1768, LPC1767, LPC1766, LPC1765, LPC1764, LPC1763,
LPC1759, LPC1758, LPC1756, LPC1754, LPC1752, LPC1751, ARM, ARM
Cortex-M3, 32-bit, USB, Ethernet, CAN, I2S, Microcontroller
Abstract
LPC176x/5x user manual


NXP Semiconductors Electronic Components Datasheet

UM10360 Datasheet

LPC17xx User manual

No Preview Available !

NXP Semiconductors
UM10360
LPC17xx user manual
Revision history
Rev Date
4.1 20161219
4 20161122
3.1 20140402
Description
LPC176x/5x user manual
Modifications:
Added a remark: The LPC175x devices require a standard I2C connection to the USB
ATX to Section 13.3 “Introduction”.
LPC176x/5x user manual
Modifications:
Updated Table 89 “Pin Mode select register 1 (PINMODE1 - address 0x4002 C044) bit
description”. Changed description to Port 0.
Added text: This bit is also cleared by an external reset to Table 8 “Reset Source Identification
register (RSID - address 0x400F C180) bit description” and added bits 4 (SYSRESET) and 5
(LOCKUP).
Fixed typo in Table 44 “Power Mode Control register (PCON - address 0x400F C0C0) bit
description”; bits 7:5 - Reserved.
Updated Table 74 “Pin description (LPC176x)”. VDD(REG)(3V3) F4 and F10 pins for WLCSP100.
Updated the address for Table 279 “UARTn FIFO Control Register (U0FCR - address
0x4000 C008, U2FCR - 0x4009 8008, U3FCR - 0x4009 C008) bit description”.
Deleted text from Section 19.1 “Basic configuration”: PINMODE_OD registers (open
drain) (See Section 8.5).
Updated Figure 124 “Center-aligned PWM waveform without dead time, POLA = 0” and
Figure 126 “Center-aligned waveform with dead time, POLA = 0”.
Updated text in Table 513 “RTC Auxiliary control register (RTC_AUX - address 0x4002 405C)
bit description”:
RTC_OSCF: RTC Oscillator Fail detect flag. Read: This bit is set when the RTC oscillator fails
to toggle on the next cycle, and when RTC power is first turned on. An interrupt occurs when
this bit is set, if enabled. The RTC_OSCFEN bit in RTC_AUXEN is a 1, and the RTC interrupt
is enabled in the NVIC.
Added text to Section 29.3 “Description”: A non-burst mode conversion requires 65
clocks and a burst mode conversion requires 64 clocks.
Updated Table 532 “A/D Control Register (AD0CR - address 0x4003 4000) bit description”:
enumerated values for bits 26:24; 010: Set the pin function to EINT0 in PINSEL4 register.and
011: Set the pin function to CAP0.1 in PINSEL3 register.
Added text: on-chip local RAM to Section 32.3.2.7 “RAM used by ISP command handler”.
Added text to the reset value in Table 524 “Watchdog Mode register (WDMOD, address
0x4000 0000) bit description”: (Only after POR).
LPC176x/5x user manual
Modifications:
Added LPC1768UK.
Table 73 “Pin description (LPC175x)” and Table 74 “Pin description (LPC176x)”: Changed
RX_MCLK and TX_MCLK type from INPUT to OUTPUT.
UM10360
User manual
All information provided in this document is subject to legal disclaimers.
Rev. 4. 1 — 19 December 2016
© NXP B.V. 2016. All rights reserved.
2 of 851


Part Number UM10360
Description LPC17xx User manual
Maker NXP Semiconductors
PDF Download

UM10360 Datasheet PDF





Similar Datasheet

1 UM10360 LPC17xx User manual
NXP Semiconductors





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy