900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf






Ramtron

FM24W256 Datasheet Preview

FM24W256 Datasheet

256Kb Wide Voltage Serial F-RAM

No Preview Available !

www.DataSheet.co.kr
Preliminary
FM24W256
256Kb Wide Voltage Serial F-RAM
Features
256K bit Ferroelectric Nonvolatile RAM
Organized as 32,768 x 8 bits
High Endurance 100 Trillion (1014) Read/Writes
38 year Data Retention (@ +75ºC)
NoDelay™ Writes
Advanced High-Reliability Ferroelectric Process
Fast Two-wire Serial Interface
Up to 1 MHz maximum bus frequency
Direct hardware replacement for EEPROM
Supports legacy timing for 100 kHz & 400 kHz
Description
The FM24W256 is a 256-kilobit nonvolatile memory
employing an advanced ferroelectric process. A
ferroelectric random access memory or F-RAM is
nonvolatile and performs reads and writes like a
RAM. It provides reliable data retention for 10 years
while eliminating the complexities, overhead, and
system level reliability problems caused by
EEPROM and other nonvolatile memories.
The FM24W256 performs write operations at bus
speed. No write delays are incurred. Data is written to
the memory array immediately after it has been
successfully transferred to the device. The next bus
cycle may commence immediately without the need
for data polling. In addition, the product offers
substantial write endurance compared with other
nonvolatile memories. The FM24W256 is capable of
supporting 1014 read/write cycles, or 100 million
times more write cycles than EEPROM.
These capabilities make the FM24W256 ideal for
nonvolatile memory applications requiring frequent
or rapid writes. Examples range from data collection
where the number of write cycles may be critical, to
demanding industrial controls where the long write
time of EEPROM can cause data loss. The
combination of features allows more frequent data
writing with less overhead for the system.
The FM24W256 provides substantial benefits to
users of serial EEPROM, yet these benefits are
available in a hardware drop-in replacement. The
FM24W256 is available in industry standard 8-pin
SOIC package using a familiar two-wire protocol. It
is guaranteed over an industrial temperature range of
-40°C to +85°C.
Low Power Operation
Wide Voltage Operation 2.7V-5.5V
100 A Active Current (100 kHz)
15 A Standby Current (typ.)
Industry Standard Configuration
Industrial Temperature -40C to +85C
8-pin “Green”/RoHS SOIC Packages
Pin Configuration
A0
A1
A2
VSS
1
2
3
4
8 VDD
7 WP
6 SCL
5 SDA
Pin Names
A0-A2
SDA
SCL
WP
VSS
VDD
Function
Device Select Address
Serial Data/Address
Serial Clock
Write Protect
Ground
Supply Voltage
Ordering Information
FM24W256-G
8-pin “Green”/RoHS SOIC
FM24W256-GTR
8-pin “Green”/RoHS SOIC, Tape
& Reel
FM24W256-EG*
8-pin “Green”/RoHS EIAJ SOIC
FM24W256-EGTR* 8-pin “Green”/RoHS EIAJ SOIC,
Tape & Reel
* Not Recommended for New Designs
This is a product that has fixed target specifications but are subject
to change pending characterization results.
Rev. 1.3
July 2011
Ramtron International Corporation
1850 Ramtron Drive, Colorado Springs, CO 80921
(800) 545-FRAM, (719) 481-7000
http://www.ramtron.com
Page 1 of 13
Datasheet pdf - http://www.DataSheet4U.net/




Ramtron

FM24W256 Datasheet Preview

FM24W256 Datasheet

256Kb Wide Voltage Serial F-RAM

No Preview Available !

www.DataSheet.co.kr
FM24W256 - 256Kb Wide Voltage I2C F-RAM
Counter
Address
Latch
4,096 x 64
FRAM Array
SDA
SCL
WP
A0-A2
Serial to Parallel
Converter
Control Logic
8
Data Latch
Figure 1. Block Diagram
Pin Description
Pin Name
A0-A2
Type
Input
SDA
I/O
SCL
WP
VDD
VSS
Input
Input
Supply
Supply
Pin Description
Device Select Address 0-2: These pins are used to select one of up to 8 devices of
the same type on the same two-wire bus. To select the device, the address value on
the three pins must match the corresponding bits contained in the slave address. The
address pins are pulled down internally.
Serial Data/Address: This is a bi-directional pin for the two-wire interface. It is
open-drain and is intended to be wire-OR’d with other devices on the two-wire bus.
The input buffer incorporates a Schmitt trigger for noise immunity and the output
driver includes slope control for falling edges. A pull-up resistor is required.
Serial Clock: The serial clock pin for the two-wire interface. Data is clocked out of
the part on the falling edge, and into the device on the rising edge. The SCL input
also incorporates a Schmitt trigger input for noise immunity.
Write Protect: When tied to VDD, addresses in the entire memory map will be write-
protected. When WP is connected to ground, all addresses may be written. This pin
is pulled down internally.
Supply Voltage: 2.7V to 5.5V
Ground
Rev. 1.3
July 2011
Page 2 of 14
Datasheet pdf - http://www.DataSheet4U.net/


Part Number FM24W256
Description 256Kb Wide Voltage Serial F-RAM
Maker Ramtron
PDF Download

FM24W256 Datasheet PDF






Similar Datasheet

1 FM24W256 256-Kbit (32 K x 8) Serial (I2C) F-RAM
Cypress Semiconductor
2 FM24W256 256Kb Wide Voltage Serial F-RAM
Ramtron





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy