900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf






Ramtron

FM25L16 Datasheet Preview

FM25L16 Datasheet

3V F-RAM Memory

No Preview Available !

www.DataSheet.co.kr
FM25L16
16Kb FRAM Serial 3V Memory
Features
16K bit Ferroelectric Nonvolatile RAM
Organized as 2,048 x 8 bits
Unlimited Read/Write Cycles
45 Year Data Retention
NoDelay™ Writes
Advanced High-Reliability Ferroelectric Process
Very Fast Serial Peripheral Interface - SPI
Up to 18 MHz Frequency
Direct Hardware Replacement for EEPROM
SPI Mode 0 & 3 (CPOL, CPHA=0,0 & 1,1)
Description
The FM25L16 is a 16-kilobit nonvolatile memory
employing an advanced ferroelectric process. A
ferroelectric random access memory or FRAM is
nonvolatile and performs reads and writes like a
RAM. It provides reliable data retention for 45 years
while eliminating the complexities, overhead, and
system level reliability problems caused by
EEPROM and other nonvolatile memories.
Unlike serial EEPROMs, the FM25L16 performs
write operations at bus speed. No write delays are
incurred. Data is written to the memory array
immediately after each byte has been transferred to
the device. The next bus cycle may commence
without the need for data polling. The product offers
virtually unlimited write endurance, orders of
magnitude more endurance than EEPROM. FRAM
also exhibits much lower power during writes than
EEPROM.
These capabilities make the FM25L16 ideal for
nonvolatile memory applications requiring frequent
or rapid writes. Examples range from data collection,
where the number of write cycles may be critical, to
demanding industrial controls where the long write
time of EEPROM can cause data loss.
The FM25L16 provides substantial benefits to users
of serial EEPROM as a hardware drop-in
replacement. The FM25L16 uses the high-speed SPI
bus, which enhances the high-speed write capability
of FRAM technology. Device specifications are
guaranteed over an industrial temperature range of
-40°C to +85°C.
This product conforms to specifications per the terms of the Ramtron
standard warranty. The product has completed Ramtron’s internal
qualification testing and has reached production status.
Rev. 3.0
Aug. 2006
Sophisticated Write Protection Scheme
Hardware Protection
Software Protection
Low Power Consumption
Low Voltage Operation 2.7-3.6V
1 µA Standby Current
Industry Standard Configuration
Industrial Temperature -40°C to +85°C
“Green”/RoHS 8-pin SOIC Package
“Green”/RoHS 8-pin TDFN Package
TDFN Footprint Conforms to TSSOP-8
Pin Configuration
CS
SO
WP
VSS
1
2
3
4
8 VDD
7 HOLD
6 SCK
5 SI
/CS 1 Top View 8 VDD
SO 2
7 /HOLD
/WP 3
6 SCK
VSS 4
5 SI
Pin Name
/CS
/WP
/HOLD
SCK
SI
SO
VDD
VSS
Function
Chip Select
Write Protect
Hold
Serial Clock
Serial Data Input
Serial Data Output
Supply Voltage
Ground
Ordering Information
FM25L16-G
“Green”/RoHS 8-pin SOIC
FM25L16-DG “Green”/RoHS 8-pin TDFN
Ramtron International Corporation
1850 Ramtron Drive, Colorado Springs, CO 80921
(800) 545-FRAM, (719) 481-7000
www.ramtron.com
Page 1 of 14
Datasheet pdf - http://www.DataSheet4U.net/




Ramtron

FM25L16 Datasheet Preview

FM25L16 Datasheet

3V F-RAM Memory

No Preview Available !

www.DataSheet.co.kr
WP
CS
HOLD
SCK
SI
Instruction Decode
Clock Generator
Control Logic
Write Protect
Instruction Register
Address Register
Counter
11
512 x 32
FRAM Array
8
Data I/O Register
3
Nonvolatile Status
Register
FM25L16
SO
Figure 1. Block Diagram
Pin Descriptions
Pin Name
/CS
I/O
Input
SCK Input
/HOLD
Input
/WP Input
SI Input
SO Output
VDD
VSS
Supply
Supply
Description
Chip Select: This active low input activates the device. When high, the device enters
low-power standby mode, ignores other inputs, and all outputs are tri-stated. When
low, the device internally activates the SCK signal. A falling edge on /CS must occur
prior to every op-code.
Serial Clock: All I/O activity is synchronized to the serial clock. Inputs are latched on
the rising edge and outputs occur on the falling edge. Since the device is static, the
clock frequency may be any value between 0 and 18 MHz and may be interrupted at
any time.
Hold: The /HOLD pin is used when the host CPU must interrupt a memory operation
for another task. When /HOLD is low, the current operation is suspended. The device
ignores any transition on SCK or /CS. All transitions on /HOLD must occur while
SCK is low.
Write Protect: This active low pin prevents write operations to the status register. This
is critical since other write protection features are controlled through the status
register. A complete explanation of write protection is provided on pages 6 and 7.
Serial Input: All data is input to the device on this pin. The pin is sampled on the
rising edge of SCK and is ignored at other times. It should always be driven to a valid
logic level to meet IDD specifications.
* SI may be connected to SO for a single pin data interface.
Serial Output: This is the data output pin. It is driven during a read and remains tri-
stated at all other times including when /HOLD is low. Data transitions are driven on
the falling edge of the serial clock.
* SO may be connected to SI for a single pin data interface.
Power Supply (2.7V to 3.6V)
Ground
Rev. 3.0
Aug. 2006
Page 2 of 14
Datasheet pdf - http://www.DataSheet4U.net/


Part Number FM25L16
Description 3V F-RAM Memory
Maker Ramtron
PDF Download

FM25L16 Datasheet PDF






Similar Datasheet

1 FM25L16 3V F-RAM Memory
Ramtron
2 FM25L16B 16-Kbit (2K x 8) Serial (SPI) F-RAM
Cypress Semiconductor
3 FM25L16B 3V F-RAM Memory
Ramtron





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy