900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




STMicroelectronics Electronic Components Datasheet

M74HCT374 Datasheet

OCTAL D-TYPE FLIP FLOP WITH 3 STATE OUTPUT HCT374 NON INVERTING - HCT534 INVERTING

No Preview Available !

M54/74HCT374
M54/74HCT534
OCTAL D-TYPE FLIP FLOP WITH 3 STATE OUTPUT
HCT374 NON INVERTING - HCT534 INVERTING
. HIGH SPEED
fMAX = 62 MHz (TYP.) AT VCC = 5 V
. LOW POWER DISSIPATION
ICC = 4 µA (MAX.) AT TA = 25 °C
. COMPATIBLE WITH TTL OUTPUTS
VIH = 2V (MIN.) VIL = 0.8V (MAX)
. OUTPUT DRIVE CAPABILITY
15 LSTTL LOADS
. SYMMETRICAL OUTPUT IMPEDANCE
IOL = IOH= 6 mA (MIN.)
. BALANCED PROPAGATION DELAYS
tPLH = tPHL
. PIN AND FUNCTION COMPATIBLE
WITH 54/74LS374/534
DESCRIPTION
B1R
(Plastic Package)
F1R
(Ceramic Package)
M 1R
(Micro Package)
C1R
(Chip Carrier)
ORDER CODES :
M54HCTXXXF1R M74HCTXXXM1R
M74HCTXXXB1R M74HCTXXXC1R
The M54/74HCT374, M54/74HCT534, are high
speed CMOS OCTAL D-TYPE FLIP FLOP WITH 3-
STATE OUTPUTS fabricated with in silicon gate
C2MOS technology. They have the same high
speed performance of LSTTL combined with true
CMOS low power comsuption. These8-bit D-type
flip-flops are controlled by a clock input (CK) and an
ouput enable input (OE). On the positive transition
of the clock, the Q outputs will be set to the logic
state that were setup at the D inputs (HCT374) or
their complements (HCT534).
While the OE input is low, the eight outputs will be
in a normal logic state (high or low logic level), and
while high level, the outputs will be in a high imped-
ance state. The output control does not affect the in-
ternal operation of flip-flops. That is, the old data can
be retained or the new data can be entered even
while the outputs are off. The application engineer
has a choice of combination of inverting and non-in-
verting outputs. The 3-state output configuration
and the wide choice of outline make bus-organized
systems simple. All inputs are equipped with protec-
tion circuits against static discharge and transient
excess voltage. This integrated circuit has input and
output characteristics that are fully compatible with
54/74 LSTTL logic families. M54/74HCT devices
are designed to directly interface HSC2MOS sys-
tems with TTL and NMOS components. They are
also plug in replacements for LSTTL devices giving
a reduction of power consumption.
PIN CONNECTION (top view)
April 1993
1/13


STMicroelectronics Electronic Components Datasheet

M74HCT374 Datasheet

OCTAL D-TYPE FLIP FLOP WITH 3 STATE OUTPUT HCT374 NON INVERTING - HCT534 INVERTING

No Preview Available !

M54/M74HCT374/534
INPUT AND OUTPUT EQUIVALENT CIRCUIT
PIN DESCRIPTION (HCT374)
PIN No
1
2, 5, 6, 9,
12, 15, 16,
19
3, 4, 7, 8,
13, 14, 17,
18
11
10
20
SYMBOL
OE
Q0 to Q7
D0 to D7
CLOCK
GND
VCC
NAME AND FUNCTION
3 State output Enable
Input (Active LOW)
3 State outputs
Data Inputs
Clock Input (LOW to
HIGH, edge triggered)
Ground (0V)
Positive Supply Voltage
IEC LOGIC SYMBOLS
HCT374
PIN DESCRIPTION (HCT534)
PIN No
1
2, 5, 6, 9,
12, 15, 16,
19
3, 4, 7, 8,
13, 14, 17,
18
11
10
20
SYMBOL
OE
Q0 to Q7
D0 to D7
CLOCK
GND
VCC
NAME AND FUNCTION
3 State output Enable
Input (Active LOW)
3 State outputs
Data Inputs
Clock Input (LOW to
HIGH, edge triggered)
Ground (0V)
Positive Supply Voltage
HCT534
2/13


Part Number M74HCT374
Description OCTAL D-TYPE FLIP FLOP WITH 3 STATE OUTPUT HCT374 NON INVERTING - HCT534 INVERTING
Maker ST Microelectronics
Total Page 13 Pages
PDF Download

M74HCT374 Datasheet PDF

View PDF for Mobile








Similar Datasheet

1 M74HCT373 OCTAL D-TYPE LATCH WITH 3 STATE OUTPUT HCT373 NON INVERTING - HCT533 INVERTING
ST Microelectronics
2 M74HCT374 OCTAL D-TYPE FLIP FLOP WITH 3 STATE OUTPUT HCT374 NON INVERTING - HCT534 INVERTING
ST Microelectronics





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy