900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Atmel Electronic Components Datasheet

45DB041B Datasheet

4-megabit 2.5-volt Only or 2.7-volt Only DataFlash

No Preview Available !

Features
Single 2.5V - 3.6V or 2.7V - 3.6V Supply
Serial Peripheral Interface (SPI) Compatible
20 MHz Max Clock Frequency
Page Program Operation
– Single Cycle Reprogram (Erase and Program)
– 2048 Pages (264 Bytes/Page) Main Memory
Supports Page and Block Erase Operations
Two 264-byte SRAM Data Buffers – Allows Receiving of Data
while Reprogramming of Nonvolatile Memory
Continuous Read Capability through Entire Array
Low Power Dissipation
– 4 mA Active Read Current Typical
– 2 µA CMOS Standby Current Typical
Hardware Data Protection Feature
100% Compatible to AT45DB041 and AT45DB041A
5.0V-tolerant Inputs: SI, SCK, CS, RESET, and WP Pins
Commercial and Industrial Temperature Ranges
4-megabit
2.5-volt Only or
2.7-volt Only
DataFlash®
Description
The AT45DB041B is a 2.5-volt or 2.7-volt only, serial interface Flash memory ideally
suited for a wide variety of digital voice-, image-, program code- and data-storage
applications. Its 4,325,376 bits of memory are organized as 2048 pages of 264 bytes
each. In addition to the main memory, the AT45DB041B also contains two SRAM data
buffers of 264 bytes each. The buffers allow receiving of data while a page in the main
memory is being reprogrammed, as well as reading or writing a continuous
data stream. EEPROM emulation (bit or byte alterability) is easily handled with a self-
AT45DB041B
Pin Configurations
Pin Name Function
CS Chip Select
SCK
Serial Clock
SI Serial Input
SO Serial Output
WP
RESET
Hardware Page Write
Protect Pin
Chip Reset
RDY/BUSY Ready/Busy
8-SOIC
SI
SCK
RESET
CS
1
2
3
4
8 SO
7 GND
6 VCC
5 WP
RDY/BUSY
RESET
WP
NC
NC
VCC
GND
NC
NC
NC
CS
SCK
SI
SO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
TSOP Top View
Type 1
28 NC
27 NC
26 NC
25 NC
24 NC
23 NC
22 NC
21 NC
20 NC
19 NC
18 NC
17 NC
16 NC
15 NC
28-SOIC
GND
NC
NC
CS
SCK
SI
SO
NC
NC
NC
NC
NC
NC
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28 VCC
27 NC
26 NC
25 WP
24 RESET
23 RDY/BUSY
22 NC
21 NC
20 NC
19 NC
18 NC
17 NC
16 NC
15 NC
CBGA Top View
through Package
12 3
A
NC NC
B
SCK GND VCC
C
CS RDY/BSY WP
D
SO SI RESET
E
NC NC NC
Rev. 1938F–DFLSH–10/02
1


Atmel Electronic Components Datasheet

45DB041B Datasheet

4-megabit 2.5-volt Only or 2.7-volt Only DataFlash

No Preview Available !

Block Diagram
Memory Array
contained three step Read-Modify-Write operation. Unlike conventional Flash memories
that are accessed randomly with multiple address lines and a parallel interface, the
DataFlash uses a SPI serial interface to sequentially access its data. DataFlash sup-
ports SPI mode 0 and mode 3. The simple serial interface facilitates hardware layout,
increases system reliability, minimizes switching noise, and reduces package size and
active pin count. The device is optimized for use in many commercial and industrial
applications where high density, low pin count, low voltage, and low power are essential.
The device operates at clock frequencies up to 20 MHz with a typical active read current
consumption of 4 mA.
To allow for simple in-system reprogrammability, the AT45DB041B does not require
high input voltages for programming. The device operates from a single power supply,
2.5V to 3.6V or 2.7V to 3.6V, for both the program and read operations. The
AT45DB041B is enabled through the chip select pin (CS) and accessed via a three-wire
interface consisting of the Serial Input (SI), Serial Output (SO), and the Serial Clock
(SCK).
All programming cycles are self-timed, and no separate erase cycle is required before
programming.
When the device is shipped from Atmel, the most significant page of the memory array
may not be erased. In other words, the contents of the last page may not be filled with
FFH.
WP FLASH MEMORY ARRAY
PAGE (264 BYTES)
SCK
CS
RESET
VCC
GND
RDY/BUSY
BUFFER 1 (264 BYTES)
BUFFER 2 (264 BYTES)
I/O INTERFACE
SI SO
To provide optimal flexibility, the memory array of the AT45DB041B is divided into three
levels of granularity comprising of sectors, blocks, and pages. The Memory Architecture
Diagram illustrates the breakdown of each level and details the number of pages per
sector and block. All program operations to the DataFlash occur on a page-by-page
basis; however, the optional erase operations can be performed at the block or page
level.
2 AT45DB041B
1938F–DFLSH–10/02


Part Number 45DB041B
Description 4-megabit 2.5-volt Only or 2.7-volt Only DataFlash
Maker ATMEL Corporation
PDF Download

45DB041B Datasheet PDF






Similar Datasheet

1 45DB041 AT45DB041
ATMEL Corporation
2 45DB041B 4-megabit 2.5-volt Only or 2.7-volt Only DataFlash
ATMEL Corporation





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z



Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy