900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Cypress Semiconductor Electronic Components Datasheet

PSoC4100BLE Datasheet

Programmable System-on-Chip

No Preview Available !

PSoC® 4: PSoC 4100_BLE
Family Datasheet
Programmable System-on-Chip (PSoC®)
General Description
PSoC® 4 is a scalable and reconfigurable platform architecture for a family of programmable embedded system controllers with an
Arm® Cortex®-M0 CPU. It combines programmable and reconfigurable analog and digital blocks with flexible automatic routing. The
PSoC 4100_BLE product family, based on this platform, is a combination of a microcontroller with an integrated Bluetooth Low Energy
(BLE), also known as Bluetooth Smart, radio and subsystem (BLESS), compliant with Bluetooth 4.2 specifications. The other features
include digital programmable logic, high-performance analog-to-digital conversion (ADC), opamps with comparator mode, and
standard communication and timing peripherals. The PSoC 4100_BLE products will be fully upward compatible with members of the
PSoC 4 platform for new applications and design needs. The programmable analog and digital subsystems allow flexibility and in-field
tuning of the design.
Features
32-bit MCU Subsystem
24-MHz Arm Cortex-M0 CPU with single-cycle multiply
Up to 256 KB of flash with Read Accelerator
Up to 32 KB of SRAM
BLE Radio and Subsystem
2.4-GHz RF transceiver with BLE 4.2 support and 50-
antenna drive
Digital PHY
Link Layer engine supporting master and slave modes
RF output power: –18 dBm to +3 dBm
RX sensitivity: –89 dBm
RX current: 16.4 mA
TX current: 15.6 mA at 0 dBm
Received Signal Strength Indication (RSSI): 1-dB resolution
Programmable Analog
Two opamps with reconfigurable high-drive external and
high-bandwidth internal drive, comparator modes, and ADC
input buffering capability; can operate in Deep-Sleep mode.
12-bit, 806 ksps SAR ADC with differential and single-ended
modes; channel sequencer with signal averaging
Two current DACs (IDACs) for general-purpose or capacitive
sensing applications on any pin
Two low-power comparators that operate in Deep-Sleep mode
Power Management
Active mode: 1.7 mA at 3-MHz flash program execution
Deep-Sleep mode: 1.3 µA with watch crystal oscillator (WCO)
on
Hibernate mode: 150 nA with RAM retention
Stop mode: 60 nA
Segment LCD Drive
LCD drive supported on all pins (common or segment)
Operates in Deep-Sleep mode with four bits per pin memory
Serial Communication
Two independent runtime reconfigurable serial
blocks (SCBs) with reconfigurable I2C, SPI, or
communication
UART function-
ality
Timing and Pulse-Width Modulation
Four 16-bit timer, counter, pulse-width modulator (TCPWM)
blocks
Center-aligned, Edge, and Pseudo-random modes
Comparator-based triggering of Kill signals for motor drive and
other high-reliability digital logic applications
Up to 36 Programmable GPIOs
7 mm × 7 mm 56-pin QFN package
3.51 mm × 3.91 mm 68-ball CSP package
Any GPIO pin can be CapSense, LCD, analog, or digital
Two overvoltage-tolerant (OVT) pins; drive modes, strengths,
and slew rates are programmable
PSoC Creator™ Design Environment
Integrated design environment (IDE) provides schematic
design entry and build (with analog and digital automatic
routing)
API components for all fixed-function and programmable
peripherals
Industry-Standard Tool Compatibility
After schematic entry, development can be done with
Arm-based industry-standard development tools
Capacitive Sensing
Cypress CapSense Sigma-Delta (CSD) provides best-in-class
SNR (> 5:1) and liquid tolerance
Cypress-supplied software component makes
capacitive-sensing design easy
Automatic hardware-tuning algorithm (SmartSense™)
Cypress Semiconductor Corporation • 198 Champion Court
Document Number: 002-23052 Rev. **
• San Jose, CA 95134-1709 • 408-943-2600
Revised February 22, 2018


Cypress Semiconductor Electronic Components Datasheet

PSoC4100BLE Datasheet

Programmable System-on-Chip

No Preview Available !

PSoC® 4: PSoC 4100_BLE
Family Datasheet
More Information
Cypress provides a wealth of data at http://www.cypress.com to help you to select the right PSoC device for your design, and to help
you to quickly and effectively integrate the device into your design. For a comprehensive list of resources, see the introduction page
for Bluetooth® Low Energy (BLE) Products. Following is an abbreviated list for PSoC 4 BLE:
Overview: PSoC Portfolio, PSoC Roadmap
Product Selectors: PSoC 1, PSoC 3, PSoC 4, PSoC 4 BLE,
PSoC 5LP. In addition, PSoC Creator includes a device
selection tool.
Application Notes: Cypress offers a large number of PSoC
application notes covering a broad range of topics, from basic
to advanced level. Recommended application notes for getting
started with PSoC 4 BLE are:
AN91267: Getting Started with PSoC 4 BLE
AN91184: PSoC 4 BLE - Designing BLE Applications
AN91162: Creating a BLE Custom Profile
AN97060: PSoC 4 BLE and PRoC BLE - Over-The-Air (OTA)
Device Firmware Upgrade (DFU) Guide
AN91445: Antenna Design and RF Layout Guidelines
AN96841: Getting Started With EZ-BLE Module
AN85951: PSoC 4 CapSense Design Guide
AN95089: PSoC 4/PRoC BLE Crystal Oscillator Selection
and Tuning Techniques
AN92584: Designing for Low Power and Estimating Battery
Life for BLE Applications
Technical Reference Manual (TRM) is in two documents:
Architecture TRM details each PSoC 4 BLE functional block.
Registers TRM describes each of the PSoC 4 registers.
Development Kits:
CY8CKIT-042-BLE-A Pioneer Kit, is a flexible, Arduino-com-
patible, BLE development kit for PSoC 4 BLE.
CY8CKIT-142, PSoC 4 BLE Module, features a PSoC 4 BLE
device, two crystals for the antenna matching network, a PCB
antenna, and other passives, while providing access to all
GPIOs of the device.
CY8CKIT-143, PSoC 4 BLE 256 KB Module, features a
PSoC 4 BLE 256 KB device, two crystals for the antenna
matching network, a PCB antenna, and other passives, while
providing access to all GPIOs of the device.
The MiniProg3 device provides an interface for flash
programming and debug.
PSoC Creator
PSoC Creator is a free Windows-based Integrated Design Environment (IDE). It enables concurrent hardware and firmware design
of PSoC 3, PSoC 4, and PSoC 5LP based systems. Create designs using classic, familiar schematic capture supported by over 100
pre-verified, production-ready PSoC Components; see the list of component datasheets. With PSoC Creator, you can:
1. Drag and drop component icons to build your hardware
system design in the main design workspace
2. Codesign your application firmware with the PSoC hardware,
using the PSoC Creator IDE C compiler
3. Configure components using the configuration tools
4. Explore the library of 100+ components
5. Review component datasheets
Figure 1. Multiple-Sensor Example Project in PSoC Creator
Document Number: 002-23052 Rev. **
Page 2 of 49


Part Number PSoC4100BLE
Description Programmable System-on-Chip
Maker Cypress Semiconductor
Total Page 30 Pages
PDF Download

PSoC4100BLE Datasheet PDF

View PDF for Mobile








Similar Datasheet

1 PSoC4100BLE Programmable System-on-Chip
Cypress Semiconductor





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy