900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Sharp Electronic Components Datasheet

LT1ED90A Datasheet

DEVICE SPECIFICATION FOR Light Emitting Diode

No Preview Available !

PREPARED BY:
JJ&,~
APPROVED BY:
DATE:
-2 ; 97
DATE:
//
s-a -y--3-1--‘I-&-_-j.&._:,,:_-f:i-.-:ii -I :,a.-- ;:,+;SPEC.No.
-_ti~~~t34-.
ELECTROMC COMPONENTS GROUP
SHARP CORPORATION
SPECIFICATION
PALa
REPRESENTATIVE DMSION:
Opto-Electronic Devices Division
DEVICE SPECIFICATION FOR
Light Emitting Diode
MODEL No.
LTlED9OA
1. These specification sheets include materials protected under the copyright of Sharp Corporation (“Sharp”).
Please do not reproduce or cause anyone to reproduce them without Sharp’s consent.
2. When using this produ& please observe the absolute maximm ratings and the instructions for use outlined
in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility
for any damageresuking from use of the product which does not comply with the absolute maximum ratings
and the instructions included in these specification sheets, and the precautions mentioned below.
(Precautions)
(1) This products is designed for use in the following application areas;
r * OA equipment * Audio visual equipment * Home appliance
L* Telecommunication equipment (Terminal)
* Tooling machines * Computers
* Measuring equipment
1
If the use of the product in the above application areas is for equipment listed in paragraphs
(2) or (3). please be sure to observe the precautions given in those respective paragraphs.
(2) Appropriate measures, such as W-safe design and redundant design considering
the safety design of the overall system and equipment, should be taken to ensure reliability
and safety when this product is used for equipment which demands high reliability and
safety in fimction and precision, such as ;
r * Transportation control and safety equipment (aircra& train, automobile etc.)
* Tra& signals * Gas leakage sensor breakers * Rescue and security equipment
1 * Other safety equipment
1
(3) Please do not use this product for equipment which require extremely high reliability
and safety in fLnction and precision, such as ;
r * Spaceequipment * Telecommunication equipment (for trunk lines)
L * Nuclear power control equipment l Medical equipment
I
(4) Please contact and consult with a Sharp sales representative if there are any questions
regarding interpretation of the above three paragraphs.
3. Please contact and consult ,tith a Sharp sales representative for any questions about this product.
CUSTOMER’S APPROVAL
DATE:
BY:
DATE:
AC. / J
PRESENTED BY.
4 Al . &,I
M.Katoh,
Department General iManager of
Engineering Dept.,111
Opto-Electronic Devices Division
Electronic Components Group
SHARP CORPORXTION
/ f7yy


Sharp Electronic Components Datasheet

LT1ED90A Datasheet

DEVICE SPECIFICATION FOR Light Emitting Diode

No Preview Available !

LTlEDSOA Srxcifmtion
1. Application
This specification applies to the light emitting diode device Model No. LTlEDSOA.
[GaPCienow-green)tG~/G~~ed)chip
LED device]
2. Outline dimensions and terminal connections . . . . . .. . . . . ..-.........Refertothe
attached sheet Page 2.
3. Ratings and characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to the attached sheet Page 3-6.
3-1. Absolute maximum ratings
3-2. Electra-optical characteristics
3-3. Derating Curve
3-4. Yellow-green Characteristics Diagram
3-5. Red Characteristics Diagram
4. Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to the attached sheet Page 7.
4- 1. Test items and test conditions
4-2. Failure judgement criteria
-,
5. lncoeg inspection . . . . . . . . . . . . . . . . . . . . ..*.......................
Refer to the attached sheet Page 8.
5- 1. Inspection method
,-.
1.
.\
5-2. Des-cription of inspection and criteria
,.:
,:‘..;
6. Taping specikation . . . . . . . . . . . . . . . . . . . . . . ..*....................*
Refer to the attached sheet Page 9- 11.
6-1. Taping
6-2. Packing specification
6-3. Label
6-4. Luminous intensity rank
7. Soldering.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..*................
7-1. Reflow soldering
>Refer to the attached sheet Page 12.
* precautions foruse...............................................
S- 1. Precautions matters for designing circuit
8-2, Cleaning method
9. Enhamenp.. . . . . . . . . *.........................................
9- 1. Ozonosphere destructive chemicals.
9-2. Bromic non-burning materials
Refer to the attached sheet Page 13.
Refer to thy attached sheet Page 13.


Part Number LT1ED90A
Description DEVICE SPECIFICATION FOR Light Emitting Diode
Maker Sharp Electrionic Components
PDF Download

LT1ED90A Datasheet PDF





Similar Datasheet

1 LT1ED90A DEVICE SPECIFICATION FOR Light Emitting Diode
Sharp Electrionic Components





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy