Datasheet4U Logo Datasheet4U.com

EDE1204 - Bi-Polar Stepper Motor IC

This page provides the datasheet information for the EDE1204, a member of the EDE1204_E Bi-Polar Stepper Motor IC family.

Features

  • the ability to change the stepping rate while the motor is stepping and to selfclock an unlimited number of steps in continuous 'RUN' mode. Inputs are TTL/ CMOS compatible. RUN mode In the 'RUN' mode, activated by a low on pin 10, the EDE1204 will cause the motor to rotate according to the following parameters: Direction (pin 7): 1 = clockwise, 0 = counter-clockwise (If a clockwise command causes counterclockwise rotation of motor, reverse the sequence of the motor’s four phase wires. ) Half-Ste.

📥 Download Datasheet

Datasheet preview – EDE1204

Datasheet Details

Part number EDE1204
Manufacturer E-Lab
File Size 208.39 KB
Description Bi-Polar Stepper Motor IC
Datasheet download datasheet EDE1204 Datasheet
Additional preview pages of the EDE1204 datasheet.

📁 Similar Datasheet

  • EDE1104AASE - (EDE1104AASE / EDE1108AASE) 1G bits DDR2 SDRAM organized (Elpida Memory)
  • EDE1108AASE - (EDE1104AASE / EDE1108AASE) 1G bits DDR2 SDRAM organized (Elpida Memory)
  • EDE1108AJBG - 1G bits DDR2 SDRAM (Elpida Memory)
  • EDE1108AJBG-8E-F - 1G bits DDR2 SDRAM (Elpida Memory)
  • EDE1116AJBG - 1G bits DDR2 SDRAM (Elpida Memory)
  • EDE1116AJBG-8E-F - 1G bits DDR2 SDRAM (Elpida Memory)
  • EDE300 - Parallel / Serial Transceiver (E-LAB Digital Engineering)
  • EDE5104ABSE - 512M bits DDR2 SDRAM (Elpida Memory)
  • EDE5104AESK - (EDE510xAESK) 512M bits DDR2 SDRAM (Elpida Memory)
  • EDE5104AGSE - (EDE510xAGSE) 512M bits DDR2 SDRAM (Elpida Memory)
Other Datasheets by E-Lab
  • EDE1200 - Unipolar Stepper Motor IC
  • EDE12400 - BI-POLAR CHOPPER STEPPER MOTOR CONTROL MODULE
  • EDE1144 - Keypad Encoder IC
  • EDE1400 - Parallel-Printer Interface

Full PDF Text Transcription

Click to expand full text
www.DataSheet4U.com EDE1204 Bi-Polar Stepper Motor IC EDE1204 Coil B Control Signal Coil B Control Signal Connect to +5V DC Connect to +5V DC Digital Ground 0 = Disable Motor Drivers 1 = Clockwise, 0 = Counter-Clockwise 1 = Normal Stepping, 0 = Half-Stepping 1 2 3 4 5 6 7 8 Coil B Coil B +5V +5V GND Free Spin Direction Half-Stepping Step Coil A Coil A OSC1 OSC2 +5V C B A Run 18 17 16 15 14 13 12 11 10 Coil A Control Signal Coil A Control Signal Oscillator Connection Oscillator Connection Connect to +5V DC Speed Control (MSB) Speed Control Speed Control (LSB) 1 = 'STEP' mode, 0 = 'RUN' mode Single-Step on Falling Edge in 'STEP' mode 9 The EDE1204 Bi-Polar Stepper Motor IC is a 5 volt, 18 pin package designed to control a Bi-Polar (4 wire) stepper motor.
Published: |